Whirlpool SF340BEH, SF357BEH manual Troubleshooting, Storage Drawer

Storage Drawer

The storage drawer can be removed. Before removing, make sure drawer is cool and empty.

To Remove:

1.Pull drawer straight out to the first stop.

2.Lift up the back of the drawer and pull out.

To Replace:

1.Fit the ends of the drawer rails into the guides in the cavity.

2.Slide the drawer closed.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Nothing will operate

■Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

■Has a household fuse been blown or has the circuit breaker been tripped?

Replace the fuse or reset the circuit.

Surface burners will not operate

■Is this the first time the surface burners have been used? Turn on any one of the surface burner knobs to release air from the gas lines.

■Is the control knob set correctly? Push in knob before turning to a setting.

■Are the burner ports clogged?

On sealed burner models, see “Sealed Surface Burners” section.

On open burner models, see “Open Burners” section.

Surface burner flames are uneven, yellow and/or noisy

■Are the burner ports clogged?

On sealed burner models, see “Sealed Surface Burners” section.

On open burner models, see “Open Burners” section.

■On models with caps, are the burner caps positioned properly?

See “Sealed Surface Burners” section.

■Is the burner damaged?

On models with caps, look for a warped cap. If cap will spin freely on a flat surface, painted side down, the cap is warped. Switch cap with a different surface burner to check for further warping. Contact a service technician or see “Assistance and Service” section.

■Is propane gas being used?

The appliance may have been converted improperly. Contact a service technician or see “Assistance and Service” section.

Surface burner makes popping noises

■Is the burner wet? Let it dry.

Excessive heat around cookware on cooktop

■Is the cookware the proper size?

Use cookware about the same size as the surface cooking area, element or surface burner. Cookware should not extend more than 1 in. (2.5 cm) outside the cooking area.

Cooktop cooking results not what expected

■Is the proper cookware being used? See “Cookware” section.

■Is the control knob set to the proper heat level? See “Cooktop Controls” section.

■Is the appliance level?

Level the appliance. See the Installation Instructions.

■On coil element models, is the element inserted properly? See “Coil Elements and Burner Bowls” section.

Oven will not operate

■Is the power outlet properly wired and polarized?

Try another outlet to check for proper wiring and polarity.

■Is this the first time the oven has been used?

Turn any one of the surface burner knobs on to release air from the gas lines.

■Is the electronic oven control set correctly? See “Electronic Oven Control” section.

■On some models, is the Control Lock set? See “Control Lock” section.

Oven makes muffled ticking noise when in use

■This is normal and occurs when the oven burner cycles on and off to hold the set oven temperature.

Oven burner lights, then goes out after 1 minute

■Press OFF/CANCEL, then wait 1 minute before trying again.

■Is the power supply properly wired and polarized? Try another outlet to check for proper wiring and polarity.

Oven burner flames are yellow or noisy

■Is propane gas being used?

The appliance may have been converted improperly. Contact a service technician or see “Assistance and Service” section.

Oven temperature too high or too low

■Does the oven temperature calibration need adjustment? See “Oven Temperature Control” section.

Display shows messages

■Is the display showing “PF”, “PF id=27” or “PF id=30”? There has been a power failure. Clear the display. See “Display(s)” section. On some models, reset the clock, if needed. See “Clock” section.

■Is the display showing a letter followed by a number? Clear the display. See “Display(s)” section. If it reappears, call for service. See “Assistance or Service” section.

14