Installing the Hood, Downdraft calibration

2/ INSTALLING THE HOOD

1)Before installing the appliance, make sure that none of the parts is damaged in any way. In case of damaged parts, contact your retailer and do not proceed with installation.

Read all of the following instructions with care before installing the appliance.

-Use an air outlet pipe of the shortest possible length.

-Limit the number of pipe bends.

-Use a material approved by standards and regulations.

- Avoid any sudden changes in pipe section (recommended constant diameter: 150 mm or equal surface area).

Before the installation of the Downdraft, please remove the security piece you can see in the picture (Fig. 1-2-3-4).

The manufacturer will not be answerable for any capacity or noise problems caused by failure to com- ply with the above instructions and the warranty will be rendered null and void.

2)Before making the opening, check that there are no structural or other parts inside the cabinet, where the appliance is to be placed, which could hinder a proper installation. Check that the dimensions of the Downdraft and the ones of the cooktop are compatible with the cabinet so that the installation can be carried out properly.

3)Make a rectangular opening measuring 490 x 104 mm in the area chosen for the cook top.

For models with motor already fitted, remove the screws and the extraction unit to fit the downdraft in the relevant hole. At this point, insert a seal (silicone) in the bottom section of the frame support (Fig.

18)and place in the relevant hole (Fig. 19-20), then proceed to insert the downdraft into the unit.

4)Put the Downdraft in the opening, inserting it from above as shown in Fig. 12.

5)The upper edge of the Downdraft must fit perfectly the cooktop.

6)Fix the Downdraft inside the cabinet. According to the dimensions of the cabinet and of the air outlet duct, use the provided fixing brackets.

Attention: do not make any additional openings on the appliance in order to avoid to damage the internal sliding and electrical components.

7)After completing the installation and connecting the appliance to the mains electricity, lift the down- draft and remove the door block (Fig. 5-6-7). Then open the door (Fig. 8 - 9), remove the PVC grease filter shield (Fig. 10), then place the filters as illustrated in Fig. 11

8)In the version of the Downdraft equipped with motor, install the motor group adjusting the air evacu- ation direction as required, either downwards or upwards. After installing the motor, connect the air ducts (Fig. 13).The motor can be fitted either on the front or back side of the downdraft..

9)For versions with outside motor, place the suction unit (outside motor) in a suitable area and fit the exhaust air flue as illustrated in Fig. 13. Proceed to fit the air outlet ducts between the outside mo- tor and the down draft. Select an air outlet from the five possibilities (Fig. 21) and fit the connection provided.

10)Put the metallic box containing the electronic components in a place easy to be reached if a technical assistance is needed Fig. 14). Connect the electrical connectors of the box to the Downdraft (Fig. 14).

11)For outside motors, connect the motor unit cable to the relevant connector on the electrical compo- nents box.

12)Power the appliance.

Downdraft calibration

After the downdraft has been installed, the aspiration panel must be calibrated. This operation is neces- sary to regulate the power exstraction of the aspiration panel. Connect the product to the power line, making sure that it is conformed to the supply voltage indicated on the technical data tag. Pushing the ON/1 button (Fig. 22B for SDD3 and 15H for SDD3 TC) the aspiration panel rises. After it has reached a height of 180mm from the cooketop, press OFF, to stop the extraction then the Timer and after 2 sec. the OFF button.

The downdraft will carry out the calibration of its aspiration panel rising and retracting for some centim- eters. During this phase, the buttons on the pushbutton control panel blink. At the end of the calibration, the aspiration panel get back to the previous position and the button end to blink. Wait until the aspiration panel stops moving before re-activating the extraction.

After the self-calibration stage, close the filter unit completely using the OFF button.

Domino S4000 specifications

The Foster Domino S4000 is a high-performance digital printer designed for businesses seeking efficiency and versatility in their printing operations. This cutting-edge device offers a range of features, technologies, and specifications that make it stand out in the competitive landscape of industrial printers.

One of the main highlights of the Domino S4000 is its advanced inkjet technology. The printer leverages a unique combination of piezoelectric print heads and high-quality ink formulations to achieve sharp, vibrant prints with exceptional color accuracy. This technology allows for high-speed printing without compromising on quality, catering to the demands of high-volume production environments.

Another notable feature is the S4000's ability to print on a wide variety of substrates. Whether it's flexible packaging, labels, or direct-to-product printing, the S4000 handles materials ranging from paper and cardboard to plastic films and metals. This adaptability makes it suitable for numerous applications across various sectors, including food and beverage, pharmaceuticals, and cosmetics.

The printer is engineered for ease of use and quick setup. An intuitive user interface facilitates seamless operation, allowing operators to manage print jobs with minimal training. The S4000 is equipped with automated workflows that optimize production efficiency, reducing downtime and increasing throughput. The system’s ability to store multiple job configurations means that setup for different print runs is swift and straightforward.

In terms of connectivity, the Domino S4000 supports a range of protocols, enabling it to integrate smoothly into existing production lines. Its compatibility with various software systems allows for sophisticated job management and tracking, enhancing the overall productivity of the printing process.

Durability is another key characteristic of the S4000. Built with robust materials and designed for long-term use, this printer can withstand the rigors of industrial environments. Maintenance requirements are minimized thanks to its reliable technology, ensuring consistent performance over time.

The Foster Domino S4000 is an exemplary solution for businesses aiming to elevate their printing capabilities. With its cutting-edge technology, versatility in substrate handling, user-friendly interface, and robust design, it delivers a combination of quality and efficiency that meets the demands of modern printing applications.