Foster FMIC180 manual Specification, Guidelines for Icemaker Bin Lids, Capacities F200 F300

F200 & F300 Modular Ice Cuber

1.Specification

1.1	Capacities
		F200	F300
Output	(kg/ 24 hours)	215	320
Bin Storage Capacity (kgs)		150/ 210	150/210
Cubes Per Cycle (kgs)		2.3	2.3
Standard Cube Size		24mm x 24mm x 26mm	24mm x 24mm x 26mm
Cycle Time (minutes)		16	11
Amps start/run		29/5.5	31/8.5
Watts Consumption		1000	1600
Machine Weight net / gross (kgs)		70/85	73/88
Refrigerant		R404A	R404A
Refrigerant Charge		500 grms	850 grms
Discharge Pressure Freeze Cycle		Max 17 bar/ Min 15 bar	Max 18 bar/ Min 16 bar
High Pressure Cut Out		30 bar	30bar
High Pressure Safety Switch		Cut in 20 bar/ Cut Out 33 bar	Cut in 20 bar/ Cut Out 33 bar
Suction Pressure Freeze Cycle		Start 3.6 bar/ End 2.3 bar	Start 3.6 bar/ 2.5 bar
Compressor Amps Freeze Mode		Start 4.2 amps/ End 3.4 amps	Start 7.0 amps/ End 5.2 amps
Voltage		230/50/1	230/50/1
Reservoir Water Level		40mm to 45mm	40mm to 45mm
Water inlet Connection		3/4 gas	3/4 gas

1.2Installation Notes.

Allow 15cm minimum space at the sides and back for ventilation.

Bin Installation

The F200 and 300 fit the New SB150 Bin.

The F200 and F300 can be fitted to the New SB210 Bin but a KN311 Lid is required.

The F200 and F300 can be fitted to the Old SB150 Bin but a SB150 frame is required, as the F200 and F300 are smaller than the Old SB150 Bin.

The F200 and the F300 can be fitted to the Old SB210 Bin provided the KN310 lid is fitted first. However it is necessary to re-drill the lid to secure the machine to it.

1.3Stacking Installation.

To stack a Modular Cuber onto the present one, first remove the top panel from the lower machine.

Add a bead of food grade silicone sealer to the top edges of the lower units freezing compartment.

Lift the top machine onto the bottom machine, (the use of a mechanical lift is recommended).

Align the two machines, and using the two screws supplied in the hardware package supplied with the top machine, fasten the two together through the fixing holes on either side of the machines.

Fit the Stacking Kit KS into the bottom machine as per the instructions supplied with the kit.

Using food grade silicone sealer, seal the edges between the freezing compartments of the top and bottom machine so as to avoid any possible leakage of water through the join.

Fig.4 Fig.5 Fig.6

13.Wiring Diagram Concerning The Connection Of Upper Ice Maker Micro To Conveyor Kit Micro

1.Detach the light blue (No.13) cable of the upper ice maker; this cable is connected to the NC contact (usually closed) of the micro. Connect it to the light blue (No.14) cable which is joined to the NO contact (usually opened) of the conveyor kit micro.

2.Connect the brown (No.16) cable which comes from the COM (common) contact of the conveyor kit micro to the NC contact (usually closed) of the upper ice maker micro.

14.Guidelines for Icemaker Bin Lids

	SB 150 BIN	NO BIN LID
FMIC 180 HEAD
	SB 210 BIN	KN 310 BIN LID
FMIC 260 HEAD	SB 150 BIN	NO BIN LID
	SB 210 BIN	KN 310 BIN LID
	SB 150 BIN	NKF 200 BIN LID
FMIF 220 HEAD
	SB 210 BIN	NKF 310 BIN LID
FMIF 550 HEAD	SB 210 BIN	NKF 310 BIN LID

4 25