Foster S4000 manual Summary of the Faults, Before Calling for Service, Tip

Page 23

EN 13/ IF OPERATING ANOMALIES OCCUR

• SUMMARY OF THE FAULTS

d01: water supply fault (tap)

d07: overflow / anti-leak fault

 

 

d02: draining fault

d08: sprinkling distribution fault

 

 

d03: heating fault

d11: pressure sensor fault

 

 

d04: temperature fault

d12: filling fault (water inlet detection system)

 

 

d05: fault – motor under load

d13: overheating fault

 

 

d06: fault - motor overload

d14 : installation fault : (incorrect drainage

connection or inadequate flow rate and tap).

 

 

 

Tip:

If one of the above faults occurs and you need to call a repair man, remember to tell him the message displayed (d01, d02..) as this information will help him.

• BEFORE CALLING FOR SERVICE

Problem

Possible Causes

What to do?

 

 

 

The door falls heavily when

- Door springs not tensioned

- Tighten the two tensioning

opened (integratable model)

enough to compensate for the

screws accessible in the bot-

 

weight of the panel.

tom section above the front

 

 

feet.

 

 

 

The door does not stay horizontal

- Door springs tensioned too

- Loosen the two tensioning

when open or returns too quickly

much.

screws accessible in the bot-

(integratable model)

 

tom section above the front

 

 

feet.

 

- No wooden panel.

- Fit a temporary wooden panel

 

 

on the appliance and adjust

 

 

the springs.

 

 

 

The door catches when closing

- Appliance not stable

- Adjust the feet.

 

- Door not centred on the tub

- Re-centre by adjusting the

 

 

rear feet.

 

 

 

The upper basket does not stay

- Poor manipulation (the basket

- Act more progressively (see

in the high position

is being pulled upwards too

instructions), one side and

 

quickly)

then the other.

 

 

 

Small leak around or under the

- Leak from the tap.

- Check that a seal is fitted and

appliance (move the appliance

- Leak from the appliance.

retighten the nut.

to locate the leak)

- Close the water tap and call a

 

(Cf. table fault d07).

technician.

 

 

 

 

 

Small leak at the door

- Appliance not stable or not level

- Adjust the feet.

 

- Door not centred on the tub.

- Re-centre by adjusting the rear

 

 

feet.

 

 

 

52

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Fully BUILT-IN Dishwasher S4000 EN Contents Use Safety InstructionsInstallation Children’s safetyEnsure that the water softener is correctly set see Environmental ProtectionECONOMICAL, Environmentally Friendly Washing Rinsing product dispenser Regenerating salt tank Waste filter Main filterPresentation of the Control Panel Detergents, rinsing liquid and an agent acting as the salt Water HardnessDetergents, rinsing liquid or an agent acting as the salt Optional Hardness Table10F SoftPowder or liquid in the distributor’s drawer Fig For Traditional ProductsTraditional tablets Loading multi-purpose tablets AdviceFor MULTI-PURPOSE Products Option Proceed to set the option, if necessaryLoading the regenerating salt Fig Regenerating salt indicatorChecking the level of rinsing liquid Adjustment leverRinsing product Fig Very important Lower BasketUpper Basket Cutlery basket slides to allow for modu- lable loading Cutlery BasketIf an anomaly occurs Total safetyAnti-overflow system Anti-leak systemWashing at 45C Rinse Hot rinse Drying Programmes TableProgramme Sequence Recommended programme EN50242 IEC 436/DIN Washing at 50C Rinse Hot rinse DryingWashing at 45C Rinse Hot rinse 60C Drying Cold pre-wash 100’ 130’Immediate programme start Stopping the appliance Cancelling a programmeSetting the audible signal ’OPTION DCS Dirt System Control BReinstallation Cleaning the Waste FiltersProfessional expertise for the general public Cleaning and upkeep of your appliancePeriodically Prolonged stoppageTip Summary of the FaultsBefore Calling for Service Relating to PROGRAMMING, Display Indicator LightsPoor Washing Results Dullness Product Setting prioritizing brilliance Tener is set correctly. Adjust itCheck the indicator light Product Setting Prioritizing DryingPoor Drying Results Poor OperationOriginal Parts Intervention WorkTests according to the mixed IEC 436/DIN 44990 method Details common to all modelsTests to Standard EN Egg/oeuf Meat/viande Spinach/épinards Foster spa
Related manuals
Manual 22 pages 5.85 Kb Manual 43 pages 27.47 Kb

S4000 specifications

The Foster S4000 is a versatile and powerful piece of equipment that has garnered attention in various industries for its impressive performance and innovative features. Designed for both efficiency and ease of use, the S4000 is suitable for a wide range of applications, from industrial settings to commercial operations.

One of the standout features of the Foster S4000 is its advanced automation capabilities. The system integrates state-of-the-art technologies that allow users to streamline processes, thereby increasing productivity. It boasts a user-friendly interface that simplifies operation, enabling even those with minimal technical skills to manage complex tasks efficiently.

At the heart of the S4000 is its robust engine, which delivers exceptional power and torque. This not only enhances the machine's performance but also contributes to its durability, ensuring it can handle demanding workloads without compromising reliability. The engine is designed to operate smoothly under various conditions, making it ideal for outdoor and indoor applications alike.

The S4000 incorporates cutting-edge sensory technology that enhances precision in operation. This technology enables real-time monitoring, allowing users to make informed decisions based on data collected during its operation. This aspect is particularly beneficial in settings where accuracy is paramount, such as manufacturing and quality control environments.

Safety is a top priority with the Foster S4000. The unit comes equipped with multiple safety features, including emergency stop buttons, overload protection, and automatic shut-off mechanisms. These features not only safeguard the operator but also prolong the life of the machine by preventing damage due to mishandling or unforeseen circumstances.

Moreover, the S4000 is designed with sustainability in mind. Its energy-efficient engine reduces fuel consumption, making it an eco-friendly option without compromising performance. The materials used in its construction are also chosen for their longevity and minimal environmental impact, contributing to a reduced carbon footprint.

In conclusion, the Foster S4000 stands out as a modern solution for various industrial and commercial applications. With its combination of advanced technologies, exceptional performance, and commitment to safety and sustainability, it is a top choice for businesses looking to enhance their operational efficiency and productivity. Its blend of power, precision, and user-friendliness makes it an indispensable asset in today’s competitive market.
Top Page Image Contents