DCS DS224 Before YOU Start Double & Single Models, Parts Supplied, Tools Needed

Page 2

R

BEFORE YOU START - DOUBLE & SINGLE MODELS

PARTS SUPPLIED

DOUBLE MODELS

Flexible Extrusion

Flexible Extrusion

Installation Tabs (2)

for Sides (2)

for Top (1)

Edge Protector (1)

Clamp

 

 

(1)

Washer

Phillips 16mm

 

 

 

 

 

(1)

Screws (7)

 

 

 

Moisture

Drain Hose

Drain Hose

Wire

Protection

Tape (1)

Support (1)

Joiner (1)

Clips (2)

p/n 527208

 

 

 

SINGLE MODELS

Wire

Edge

Clip (1)

 

Protector (1)

Drain Hose

Support (1)

Drain Hose

Joiner (1)

Flexible Extrusion for Sides (2)

Clamp (1)

 

Phillips 16mm Screws (5)

Moisture Protection Tape (1) p/n 527208

Washer (1)

Prefinished

Toe Kick (1)

White prefinished toe kick kit p/n 526678 or Black prefinished toe kick kit p/n 526679

or Iridium prefinished toe kick kit p/n 527109

TOOLS NEEDED

Wooden Chopping Board

Drill & No.2 Phillips Bit

Tape Measure

No.2 Phillips Screwdriver

Spirit Level

Flat Screwdriver

Safety Glasses

Adjustable Wrench or M5 Socket

Utility Knife

Ø11/2” (38mm) Hole Saw

Pencil

Side Cutting Pliers

Sandpaper

 

SPARE PARTS INSTALLATION KIT FOR SINGLE & DOUBLE MODELS: p/n 526676

INSTALLATION PREPARATION

ELECTRICAL PREPARATION

A)The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after installation.

B)The switched power outlet must be between 6” (150mm) and 18” (450mm) from the DishDrawer® cavity.

C)Refer to Page 9, Step 5 for electrical connection options.

Important!

The services hole in the DishDrawer® cavity needs to be large enough for the plug on the power supply cord to fit through, but MUST NOT be more than 11/2” (38mm).

PLUMBING & DRAINAGE PREPARATION

A)A readily accessible valve must be installed in the water supply pipe.

B)If the supply pressure exceeds 145 psi (1000kPa), then a pressure limiting valve must be used.

C)Review Plumbing Options on pages 4 & 6. Choose a method that best suits your needs.

D)A Drain Hose extension Kit P/N 525798 will extend the drain hoses by 1413/4” (3.6m). The kit is available from the nearest Fisher&Paykel Authorized Service Agent. DO NOT extend beyond this limit.

E)This Dishwasher’s maximum drain height is 371/2” (950mm).

CAVITY PREPARATION

A)It is recommended that all cabinetry surrounding the DishDrawer® (including the underside of the countertop) is sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam

damage. The air in the cavity can get very hot and humid (saturated at 122oF/50oC)

B)The self-adhesive moisture protection tape must be applied to the underside of the countertop to prevent moisture damage, (refer to cavity diagram pg 3 or 5). Be sure surfaces are dry and dust-free prior to application.

C)Be sure the cavity provides sufficient material to secure the DishDrawer® using the mounting tabs (refer to step 1, page 7). If there is

nothing to screw to, add a brace. See page 3 or 5 for screw locations.

D)The services hole MUST be immediately adjacent to the rear lower corner of the cabinetry. If not, the hoses will prevent the DishDrawer® being pushed back into the cavity all the way. The hole

can be located on either side depending on the location of the services.

E)Be sure the cavity sides are plumb (vertical) as this will assist with levelling the DishDrawer® .

F)Minimum clearances:

1/8(2.5mm)

1/8(2.5mm)

1/2(13mm)

ELECTRICAL INFORMATION

POWER SUPPLY CORD

A)Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord.

B)If the power supply cord is damaged, it must be replaced by the Manufacturer, Service Agent or a similarly qualified person in order to avoid a hazard.

GROUNDING INSTRUCTIONS

A)This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

WARNING!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

B)This appliance is equipped with a power supply cord having an equipment-grounding conductor and an earthing plug. The power supply plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local Codes and Ordinances.

WARNING!

Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adaptor plug or multiple

2

Image 2
Contents Installation Instructions Parts Supplied Installation PreparationBefore YOU Start Double & Single Models Tools NeededWater Softener Models Services SpecificationsDouble Models Drain ConnectionPlumbing Options OptionSingle Models CavityOption Mounting TAB Options Installation InstructionsRemoving the TUB Adjusting the Feet Double Models only Securing the ProductElectrical Connection Refitting the TUBAt this stage Connecting the Inlet HoseDo not plug the product Remove all sharp edges Measuring the TOE Kick Double Models onlyTrimming the TOE Kick Double Models only Customer Care FinalchecklistdoubleandsinglemodelsTrouble Shooting For the United States of America USA & Canada

DS224 specifications

The DCS DS224 is a high-performance, versatile storage solution designed for small to medium-sized businesses that require reliable data management and accessibility. It boasts a sleek and compact design, allowing for easy integration into various IT environments without consuming excessive space. The DS224 is engineered for optimal performance, featuring dual controllers that maximize throughput and redundancy, ensuring continuous availability of critical data even in the event of a hardware failure.

One of the standout features of the DCS DS224 is its expansive storage capacity. The device supports multiple drive configurations, allowing users to mix and match SSDs and HDDs to achieve a balance between performance and cost-efficiency. This flexibility empowers organizations to customize their storage architecture based on specific requirements, such as high-speed access for critical workloads or larger capacity for archiving purposes.

In terms of connectivity, the DS224 incorporates multiple interfaces, including 10GbE and 1GbE networking options, which facilitate seamless integration with existing infrastructure. The ability to connect to various networks not only enhances data transfer speeds but also streamlines access to virtual machines and other critical applications hosted on the device.

The DCS DS224 is equipped with advanced data protection technologies. Its built-in snapshot capabilities enable users to take point-in-time backups, ensuring that valuable data remains secure and recoverable in the event of accidental deletion or corruption. Additionally, the system includes support for dynamic RAID configurations, allowing for on-the-fly changes without downtime, minimizing disruption to business operations.

Management and monitoring of the DS224 are user-friendly, thanks to its intuitive web interface and comprehensive management tools. Administrators gain access to real-time performance metrics and health indicators, facilitating proactive maintenance and optimized resource allocation. Furthermore, the device supports various virtualization technologies, making it a suitable choice for organizations looking to streamline their virtual environments.

In conclusion, the DCS DS224 represents a robust and adaptable storage solution, equipped with features and technologies that cater to the diverse needs of modern businesses. Its blend of performance, scalability, and advanced data protection ensures that organizations can effectively manage their data while maintaining high levels of efficiency and security.