DVD & CD Mode
Playing DVD and CDs
In DVD & CD Mode, the DKEC can play DVDs and music CDs.
To play a DVD or CD:
1.Press 
on the front panel of the DKEC to open the disc tray.
2.Place the disc with its label side up onto the tray.
3.Press 
to close the tray.
4.The disc will play automatically. DVDs will typically display a menu.
General Commands
The following table lists additional tasks and commands:
To... | Do this... |
|
Stop the disc. | On the remote or |
|
| keyboard, press . |
|
Pause the disc. | On the remote or |
|
| keyboard, press . |
|
Resume a paused | On the remote or |
|
disc. | keyboard, press . |
|
Move forward or | On the remote or |
|
backwards in the | keyboard, press | or |
disc. | . Press again to |
|
| increase or decrease | |
| the speed backwards | |
| or forward. Press | to |
| resume playing the disc. | |
Automatically | On the remote or |
|
repeat the disc. | keyboard, press Repeat. | |
| Press again to turn off | |
| repeat function. |
|
Play the next or | On the remote or |
|
previous DVD | keyboard, press | or |
chapter. | . |
|
Display DVD | On the remote or |
|
menu. | keyboard, press Menu. | |
Watch DVD with | On the remote or |
|
subtitles. | keyboard, press |
|
| Subtitle. |
|
| Press again to turn off | |
| subtitles. |
|
Change angle on | On the remote or |
|
DVDs that feature | keyboard, press Angle. | |
different camera | Press again to see other | |
angles. | camera angles. |
|
Change zoom | On the remote or |
|
level on DVDs. | keyboard, press Zoom. | |
| Press again to see other | |
| zoom options. |
|
Change DVD | On the remote or |
|
audio track | keyboard, press Audio. | |
options. | Press again to see other | |
| audio track options. |
|
Go to a specific | On the remote or |
|
CD track. | keyboard, enter the |
|
| number of the track, |
|
| then press GO. |
|
Play the next or | On the remote or |
|
previous CD track. | keyboard, press | or |
| . |
|
Randomize CD | On the remote or |
tracks | keyboard, press |
| Random. |
| Press again to turn off |
| random function. |
3D Audio
3D Audio is an optional audio setting that may enhance the listening quality of some DVD and CDs.
To listen with 3D Audio:
1.Press 3D Audio.
2.Press again to turn 3D Audio off.
Internet Mode
You can browse the Internet on your DKEC using Internet Mode. Using the remote, keyboard and touch screen, you can browse web sites, check email and look up useful information in the kitchen. You can specify a default home and email web page for quick access.
Before browsing you may need to configure your Internet connection. If your DKEC was professionally installed, it is most likely already configured for Internet Mode. If it was not, you will need to contact your Internet service provider (ISP) for information needed to configure the DKEC.
Note:
You can find more information about configuring an Internet connection in the DKEC Help. Press Help in Internet Mode and select Connecting to the Internet.
Internet Options Menu
Configuring Connection Settings
The DKEC can connect to the Internet in three different ways:
•Wired (Ethernet) Broadband
•Wireless (802.11b) Broadband
•
Configuring a Wired Broadband Connection If you’ve installed the included PCMCIA Network card for a wired (ethernet) Broadband connection, further configuration may not be needed. The DKEC is set by default to support DHCP (Dynamic Host Configuration Protocol), which is suitable for most households. If your Internet Service Provider (ISP) support DHCP, the DKEC should connect automatically when you go to Internet Mode.
However, if you use a Static IP address further information is required to connect. Your ISP will need to provide you with a static IP address, subnet mask, gateway router and DNS servers.
To configure a Broadband connection:
1.Press Internet to switch to Internet Mode, then press Options.
2.From the Internet Options menu, select Connection Settings.
3.Select the Broadband Settings button.
4.Select the Ethernet Type.
•Select the Use DHCP (Auto) if your ISP supports dynamic host configuration protocol (DHCP).
•Clear the Use DHCP (Auto) checkbox if your ISP does not support DHCP.
5.If needed, enter static IP address, subnet mask, gateway router and DNS servers.
6.Choose OK.
Configuring a Wireless Connection
If you are using a wireless network card, you’ll need to configure the connection settings the first time you go to Internet Mode. This may include a WEP (Wired Equivalent Privacy) key and other security settings. This may also include additional IP information if you use a Static IP address.
To configure a Wireless connection:
1.In Internet Mode, press Options.
2.From the Internet Options menu, select Connection Settings.
3.Select the Wireless Settings button.
4.Select your home network.
5.If your network requires a WEP key, select the Security button, then:
a.Select the appropriate security options.
b.Enter the WEP key.
c.Choose OK.
6.If you use a static IP address, select the IP button, then:
a.Clear the Use DHCP (Auto) checkbox.
b.Enter static IP address, subnet mask, gateway router and DNS servers.
c.Choose OK.
7.Choose the Connect button.
a.If the connection is successful, the Options dialog closes.
b.If the connection is not successful, the Options dialog remains open so you can resolve the issue.