QSC Audio RAVE 520uz manual Getting Started, Reboot only if your computer prompts you to do so

Page 18

Getting Started

This section outlines one of the simpler methods of getting familiar with your RAVE and the QSControl.net software. The goal of this procedure is to get your computer and the RAVE connected and communicating and the QSControl.net software installed and running. After the software is installed and running, refer to the software’s Help file for all software related operation/issues. Note! The default password for the RAVE is “qsc” (no quotes, lower case).

1- Turn off the computer and unplug the power cord from the RAVE 520uz.

2- Connect a CAT-5 crossover cable from the computer’s network interface card (NIC) to the RAVE QSControl jack (example 1, page 6).

3- Reconnect the power cord to the RAVE 520uz (turn it on). Using the RAVE LCD display and controls, navigate the menu to the IP Address and make a note of it. In steps 12 and on, you will need to change the IP address of the RAVE or your PC.

4- Turn on the PC and start Windows. You must have Administrator rights and be signed on as Administrator in order to install the QSControl.net program. Ensure you are signed on to the computer as the Administrator.

5- Place the QSControl.net CD-ROM in your CD-ROM drive. The install wizard should start. If not, you can also select Start, then Run and browse for the file named setup.exe from the CD.

6- The installer queries the computer for available drive space and other information. If required MDAC library (Microsoft) files are not already on the computer, the library files are installed. You must accept the Microsoft software agreement in order to install the MDAC library. It may be necessary to reboot the computer after library installation.

7- At the prompt for “Client/Server” selection, keep both Client and Server selected. This will be appropriate for general use.

8- When prompted “Select Installation Folder”, specify the installation directory or accept the default location.

9- You will be prompted to select an installation accessible by everyone (non-secure) or an installation accessible only to you (secure). Select the appropriate Everyone or Just Me box and continue. Installation proceeds.

10- Reboot only if your computer prompts you to do so.

11- Select Network Connections in the control panel. Select Properties. Right-click Local Area Connection, and view its proper- ties. Highlight the Internet Protocol (TCP/IP) tab and view its properties. You will see an entry field for the IP address. Decide whether you want to change the IP address of your computer to be similar that of to the RAVE (easiest if you have many RAVE units) or if you want to change the IP address of your RAVE to be similar to that of the computer. This is a network management decision.

12- Change the IP address of the RAVE (or computer) to be compatible with that of the computer (or RAVE). Typically, this is done by making the IP address of one of the devices 1 digit different in the last octet (group of digits in IP address). If changing the computer’s settings, write down the current values, in case you want to revert later.

13- The subnet mask address should be exactly the same for both the computer and the RAVE. The Gateway address should not be altered as it is not used.

14- After you are satisfied with all your settings, close all open windows and start the QSControl.net program. Select Start, All Pro- grams, QSControl.net, Venue Manager.

15- The login screen should open. The default password is “qsc” (lower case, no quotation marks). Select “Log on to Local Computer” and click OK.

16-The QSControl.net Venue Manager window will open. A Startup Tips screen will be visible the first time Venue Manager is launched. Optionally, the Startup Tips screen may be disabled by un-checking the box in it’s lower left corner. It is highly recom- mended the user become familiar with each of the tips listed on this screen. After reviewing the tip(s), close the Startup Tips screen.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Input CobraNet Enabled Signal Processor Hardware Manual TD-000201-00Important Safety Precautions & Explanation of Symbols Introduction See page 14 for detailed descriptionsBlock Diagram Why CobraNet Needs Special Treatment Introduction Networking the Rave 520uzExample #1 QSControl.net X-over mode Example #2 CobraNet X-over mode Example #3 Single Wire Interface Example #4 Two-Wire Interface shared network hardware Example #5 Two-Wire Interface separate network hardware Rack Mounting UnpackingMounting DescriptionTo Uninstall QSControl.net Computer Requirements & Software InstallationTo Install QSControl.net Click the Install QSControl.net buttonNetwork General Information & Configuration MemoriesConfiguration Memories CobraNet Connection LossConnections LED Indicators Relay OutRS-232 Front Panel Password Lockout LCD Display and ControlsLCD Navigation Map Reboot only if your computer prompts you to do so Getting StartedGetting Started Operation How to put the Rave 520uz into safe mode Utility/Diagnostic FunctionsSafeMode Switch RS-232 Serial Port I/O InterfaceRS-232 Communications Procedure Telnet Access Preliminary Specification Weight IndicatorsDimensions Relay OutputsDimensions Page How to Contact QSC Audio Products QSC Audio Products 3 Year Limited Warranty

RAVE 520uz specifications

The QSC Audio RAVE 520uz is an innovative addition to the world of portable professional audio systems, designed to deliver high-quality sound performance in a compact and versatile package. Ideal for live events, conferences, and installations, the RAVE 520uz embodies QSC's commitment to excellence in audio technology.

One of the standout features of the RAVE 520uz is its robust amplifier, capable of delivering an impressive power output. This amplification ensures that even in larger venues, the audio remains clear and impactful. The system's high-efficiency design not only contributes to its powerful sound but also enhances energy savings, making it an environmentally friendly choice for users.

Complementing the amplifier is the advanced loudspeaker design, which includes a high-frequency driver and a custom woofer. This combination enables a wide frequency response, allowing for clear distinction between lows, mids, and highs. The result is a well-balanced sound that is perfect for various applications, from live music performances to spoken word events.

Another key characteristic of the RAVE 520uz is its user-friendly interface. Intuitive controls and programmable presets allow for quick setup and adjustments, catering to users of all experience levels. This accessibility makes it a popular choice among sound engineers as well as casual users who may not have extensive technical knowledge.

In terms of connectivity, the RAVE 520uz is equipped with multiple input options, including standard XLR and TRS connectors, making it compatible with a wide range of audio sources. Additionally, Bluetooth capabilities enable wireless streaming, adding flexibility for live performances and event setups.

Durability is also a focus in the design of the RAVE 520uz. Built with high-quality materials, the unit is designed to withstand the rigors of transporting and frequent use, making it a reliable partner for touring professionals and venues alike.

Overall, the QSC Audio RAVE 520uz stands out as a powerful, versatile, and user-friendly audio solution. With its combination of high performance, ease of use, and robust construction, it meets the demands of various audio applications while delivering exceptional sound quality consistently. Whether you're a seasoned audio professional or someone looking to enhance their event experience, the RAVE 520uz is a worthy consideration in the portable audio market.
Top Page Image Contents