Installing Refrigerator in Enclosure

12 Volts DC Connection

The refrigerator model NDR 1292 - S require a continu - ous 12 volt DC supply (even though 2-way models are designed to operate on 120 volts AC and gas, a 12 volt DC control is required to maintain the automatic energy

system). The connection is made to the positive (t) and negative (-) terminals of the terminal block on the back of the refrigerator. (See FIG. 1). Correct polarity must be observed when connecting to the DC supply.

Do not use the chassis or vehicle frame as one of the conductors .

Connect two wires at the refrigerator and route to the DC supply.

The distance the current must travel from the battery to the refrigerator dictates the AWG wire size to be used. Should the wire be too small for the distance, a voltage drop will result.

Recommended wire sizes are shown below .

MAXIM”?4 TOTAL CONDUCTOR WIRE LENGHT (in feet and meters,

The wires from the battery to the refrigerator must be of large enough size to handle the load. The connections must be clean, tight and free from corrosion.

The transport support at the rear of the refrigerator can be removed if necessary for the installation of the refrig- erator in the enclosure. (See figure above).

NOTE: DO NOT install the appliance directly on carpeting. Carpeting must be removed or protected by a metal or wood panel beneath the appliance, which extends at least full width and depth of the appliance.

Caution: Use care when installing the refrigerator. This refrigerator is equipped with the latest vacuum insulated panel technology . These insulating panels are located on the Top, Back, Bottom, Sides and Doors of the refrig- erator .

If the surface is punctured, loss of insulation will occur. resulting in poor refrigerator performance.

NOTE: A wood strip must be in place across the upper opening of the enclosure. The top frame of the refrigera- tor will be anchored to the wood strip with screws. see FIG. 10.

The refrigerator must be installed in a substantial enclo- sure and must be level. When installing the refrigerator in the enclosure, all areas within the recess in which the refrigerator is installed must be sealed.

Make sure that there is a complete seal between the front frame of the refrigerator and the top, sides and bottom of the enclosure. A length of sealing strip is ap- plied to the rear surface of the front frame for this pur- pose, sea FIG. 4. The sealing should provide a com- plete isolation of the appliance’s combustion system from the vehicle interior.

NOTE: Be careful not to damage the sealing strip when the refrigerator is put in place.

FIG. 4

Securing the Refrigerator

After the refrigerator is put in place, (ensuring a com- bustion seal at the front frame), the refrigerator is to be secured in the enclosure with six straws (not included). The screws have to be installed in the following order:

STEP 1: Two screws installed through the front base,

which includes the lower front strip installation.

The refrigerator is provided with a lower front strip (shipped as a loose part). The front strip is to be attached after the refrigerator is set into the cutout opening.

1.Install the lower front strip by sliding it under the bottom hinge plates, as shown in FIG. 5.

NDR1292-S specifications

The Dometic NDR1292-S is a reliable and versatile refrigerator designed for those who enjoy the outdoor lifestyle, whether camping, traveling in a caravan, or spending weekends at the cabin. This absorption fridge combines efficiency with advanced technology to ensure that food and beverages remain perfectly chilled, no matter where your adventures take you.

One of the standout features of the Dometic NDR1292-S is its impressive cooling capacity. With a total gross volume of approximately 96 liters, it provides ample storage space for perishable items, drinks, and other essentials. The refrigerator compartment is designed to keep your food fresh at selected temperatures, while the separate freezer compartment allows for long-term storage of frozen goods. This dual-zone design is particularly beneficial for those who wish to maintain a variety of food options while on the road.

The NDR1292-S utilizes absorption refrigeration technology, which allows it to operate quietly and efficiently, making it an excellent choice for those who prefer a peaceful environment. This technology allows the fridge to run on multiple power sources: 12V from the vehicle’s battery, 230V AC mains power, or gas. Such versatility makes it suitable for various situations, from driving across the country to living off-grid. This system also ensures minimal energy consumption, enhancing the overall efficiency of the unit.

The features of the Dometic NDR1292-S extend beyond cooling. The fridge is designed with user-friendly controls, making it easy to set and adjust the temperature according to your preferences. It also includes an adjustable shelving system, maximizing the use of available space and allowing for customizable organization of food items.

Another characteristic that sets the Dometic NDR1292-S apart is its robust design, built to withstand the rigors of travel. The exterior is constructed from durable materials that resist wear and tear, while the refrigerator's insulation is designed to maintain internal temperatures effectively, even in warm environments.

In summary, the Dometic NDR1292-S is a powerful and efficient refrigeration solution, offering generous storage capacity, flexible power options, and smart design features. Perfect for adventure enthusiasts and outdoor lovers, it ensures that users can enjoy fresh food and cold drinks wherever they may roam. With its combination of reliability, efficiency, and user-friendly design, the Dometic NDR1292-S stands out as a top choice for portable refrigeration needs.