Whirlpool ET14JK warranty Adjusting the Shelves, Removing the Crisper and Crisper Cover

Pull Shelf Out Until It Stops. Lift the Front and Pull Agarn

Lift the Front, Then the Back -

Adjusting the Shelves.

Adjust your refrigerator shelves to match your food storage needs for tall items, short items or sizes in between. It will be easier to move a shelf if you take off all the food first.

Slide the shelf you want to move toward you until it stops. Lift up the front and slide it out the rest of the way. To put it back on the shelf guides, fit the back of the shelf on top of the guides with the wire stops on the bottom of the guides. Slide it in, keeping the front litted up until the stops on the shelves clear the stops on the guides.

Removing the Crisper and Crisper Cover.

To remove the crisper, slide it out until it stops. Lift the front a little and slide it out the rest of the way.

The cover rests on nubs built into the side walls of the refrigerator. To remove the cover, lift the front and then the back. To replace the cover, fit the notches in the back corners of the cover over the nubs at the back of the walls. Then lower the front into place.

To replace the crrsper, slide It in, keeping the front lifted a little until the crisper clears the stops

Pull out to stop. -

Lift the Front and Pull Again.

Replacing the Light Bulb.

WARNING: Before removing the light bulb, either unplug the re- frigerator or disconnect the electricity leading to the refrigerator at the main power supply. Shock and injury can occur if electricity remains connected. To replace bulb, reach behind the control con- sole to find the bulb. Remove bulb and replace it with a 40-watt ap- pliance bulb.

Ice Cube Trays.

To remove ice from the flexible ice trays, hold a tray at both ends, as shown. Slightly twist the tray; the ice will come out easily.

If cubes are not used for a number of weeks, they may become smaller. The moving air is so cold that it starts a slow evaporation. [That’s also why it’s so important to wrap food carefully.) The longer they are stored, the smaller they can get.

A Twist of the Wrists

Raise Signal

Arm to Stop Ice Maker Lower Signal

Arm to Start It

Optional ICE MAGIC” Automatic Ice Maker.

If you have the automatic ice maker accessory or plan to add one later [Part No. ECKMF-83) there are a few things you will want to know.

lThe ON I OFF lever IS a wtre signal arm. Down...for making Ice automatically;

Up .to shut off the Ice maker

l

Shake

the

brn

occaslonally

to

keep cubes

separated,

and

to

obtain

Increased

storage

capacity.

l

It IS normal

for

Ice

crescents

to

be attached

by

a corner.

They

will break

apart

easily

l

You

wtll

hear

water running when Ice maker is working. You’ll hear ice

fall Into the bin. Don’t let these sounds bother you.

l

The

Ice

maker

will

not operate

until

the

freezer

is cold enough

to make

Ice. This can take overnight

.

Because

of

new

plumbing

connecttons,

the

first Ice

may

be

discolored

or

off-flavored.

Discard

the

ftrst few

batches

of

ice.

l

If ice

is not

being

made

fast

enough

and

mcxe

ice

is needed,

turn

the

Refrigerator

Control toward a higher number. Wait a day and, if nec-

essary, turn the Freezer Control toward A

l

If you

remove

the

ice bin, raise the signal arm to shut off the Ice maker.

When you return the bin, push it all the way in and lower the arm to the

ON

position

l

If cubes

are

stored

too long, they may develop

an

off-flavor.like

stale

water

Throw

them

away.

They

will

be

replaced,

Cubes

in the

ice

bin

can

also

become

smaller

by

evaporation.

l

The

ICE: maker

water supply

should

not

be

softened

water.

The

chem-

icals

could

damage

the

Ice

maker

rnolds

5