Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

■	Flat-blade screwdriver	■	¹⁄₄" Drill bit
■	⁷⁄₁₆" and ¹⁄₂" Open-end or two	■	Hand drill or electric drill
	adjustable wrenches		(properly grounded)

■¹⁄₄" nut driver

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

■All installations must meet local plumbing code requirements.

■Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber.

ConnecttheWater Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.

	A
G	B
G
	C
F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shutoff valve
C. Copper tubing	G. Packing nut
D. Compression nut

ET1FHTXMQ00, ET1FHTXMB02, ET1FHTXMB03, ET1FHTXMT02, ET1FHTXMQ03 specifications

The Whirlpool ET1FHTXMB01, ET1FHTXMT01, and ET1FHTXMQ01 refrigerators stand out in the market for their combination of innovative features, sleek design, and practical functionality. Each model shares a commitment to providing efficient cooling solutions suitable for various kitchen environments.

One of the most notable features of these refrigerators is their spacious interior layout. With adjustable shelves and door bins, users can customize the storage space to accommodate different food items and containers. This flexibility is especially beneficial for families or individuals who frequently purchase large quantities of groceries. The clear crisper drawers for fruits and vegetables ensure freshness and visibility, helping consumers maintain a healthy lifestyle.

Energy efficiency is a major focus of Whirlpool’s design philosophy. The ET1FHTXMB01, ET1FHTXMT01, and ET1FHTXMQ01 models are Energy Star certified, which means they meet strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This certification not only helps reduce carbon footprints but also lowers utility bills for users. The advanced cooling system regulates temperature effectively, ensuring that food stays fresh longer while using minimal energy.

Another significant characteristic of these refrigerators is their user-friendly temperature controls. The easy-to-use mechanical controls allow for precise temperature adjustments, ensuring optimal cooling for different types of food. In addition, the models are equipped with a frost-free defrost system, which prevents the buildup of ice and eliminates the need for manual defrosting, thus saving time and effort.

The sleek, modern design of these refrigerators enhances the aesthetics of any kitchen. Available in various finishes, including black, white, and stainless steel, they can seamlessly integrate with different décor styles. The textured finish also helps hide fingerprints and smudges, making maintenance easier.

In terms of technology, these refrigerators feature advanced cooling technologies that help maintain consistent temperatures throughout the unit. With the inclusion of enhanced airflow systems, items stored at different levels receive uniform cooling, further supporting food preservation.

Overall, the Whirlpool ET1FHTXMB01, ET1FHTXMT01, and ET1FHTXMQ01 refrigerators offer a compelling combination of design, efficiency, and functionality. Whether used in small apartments or larger homes, they provide a reliable solution for keeping food fresh while also contributing to energy savings and a cleaner environment.