Whirlpool GR2SHTXKQ02 Door Closing and Alignment, Using the Controls, Adjusting Control Settings

Mid-setting “3”

Door Closing and Alignment

Door Closing

Your refrigerator has two front adjustable rollers – one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using the instructions below:

1.Plug into a grounded 3 prong outlet.

2.Move the refrigerator into its final position.

3.Remove the base grille (see “Base Grille” earlier in this section). The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side.

4.Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

5.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

6.Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it using the instructions below:

1.Pry off the top hinge cover.

2.Loosen the top hinge screws using a ⁵⁄₁₆ in. socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4.Replace the top hinge cover.

Using the Control(s)

For your convenience, your refrigerator control(s) are preset at the factory. When you first install your refrigerator, make sure that the control(s) are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to the word OFF or until the word OFF appears. Your product will not cool when the refrigerator control is set to OFF.

Mid-setting “3”

Mid-setting “4”

REFRIGERATOR 4 4 FREEZER

IMPORTANT:

■Give your refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator.

■If you add food before the refrigerator has cooled completely, your food may spoil. Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

Adjusting Control Settings

The mid-settings indicated in the previous section should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the chart below as a guide. On models with two controls, adjust the refrigerator temperature first. Wait at least 24 hours between adjustments and then recheck the temperatures.

CONDITION/REASON:	ADJUSTMENT:
REFRIGERATOR too warm	REFRIGERATOR or
	TEMPERATURE Control one
	setting higher
FREEZER too warm/too	FREEZER or TEMPERATURE
little ice	Control one setting higher
	MAX ice production switch
REFRIGERATOR too cold	REFRIGERATOR or
	TEMPERATURE Control one
	setting lower
FREEZER too cold	FREEZER or TEMPERATURE
	Control one setting lower

Crisper Humidity Control

(on some models)

You can adjust the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins. HIGH (closed) for best storage of fresh, leafy vegetables.

8