QSC Audio CM16a manual Specifications, Input Signal Processing, Power amplifier output processing

Page 33

Section 4: Specifications

Input Signal Processing

Frequency response

20 Hz–20 kHz ±0.5 dB

 

10 Hz–80 kHz ±3 dB

 

 

Distortion

<0.01% THD+N @ +4 dBu out

 

(page input <0.03%)

 

 

Dynamic range

>110 dB unweighted

 

20 Hz–20 kHz

 

(page input >100 dB)

 

 

Polarity

In-phase or inverted

 

 

Level control range

-95.5 to 0 dB in 0.5 dB steps

 

 

Precision attenuator

better than 112 dB below

transients (“zipper”

maximum output

noise)

 

 

 

Mute

>90 dB attenuation

 

 

Inputs

 

Program inputs

16

Paging inputs

1

Monitor bus input

1

Connector type

“Phoenix-style” (a.k.a.

 

“Euro-style”) detachable

 

terminal blocks

Type

Electronically balanced

Grounding

All shield terminals connected to

 

chassis

Nominal level

1V/3V rms selectable

Maximum level

+21 dBu

Impedance

10 kOhm balanced

Common-mode rejection

Typical, >50 dB, 20 Hz–20 kHz

 

Worst Case, >40 dB at 20 kHz

Crosstalk (inter-

>75 dB separation, 20 Hz–20 kHz

channel within

 

Data Port pair)

 

Crosstalk (intra-

>85 dB separation,

channel, between

20 Hz–20 kHz

Data Port pairs)

measured with all inputs and

 

outputs terminated

 

 

Outputs

 

Program outputs

16 (via HD-15)

Connector type

8 HD-15 data port connections

Pinout

Special, see appendix

Cable type

VGA monitor cable

Qualified length

2 meters

Monitor output

1

Connector

“Phoenix-style” (a.k.a.

 

“Euro-style”) detachable

 

terminal blocks

Type

Electronically balanced

Grounding

Shield terminal connected to

 

chassis

Nominal level

+4 dBu

Maximum level

+21 dBu

Output impedance

75 Ohms balanced

Output load

600 Ohms minimum

Power amplifier output processing

Power amplifier output monitoring

Output short detect*

Senses load <1 Ohm for Stereo/

 

Parallel modes; <2 Ohms in Bridged Mono mode

 

Threshold is adjustable in software

Output open detect*

Senses load >60 Ohms

 

Threshold is adjustable in software

Output voltage meter

Range automatically matches to

 

amplifier model used

Output current meter

Range automatically matches to

 

amplifier model used

*Signal level must be greater than -32 dB, referenced to maximum output of amplifier

33

Image 33
Contents CM16a Amplifier Network Monitor ¨ Warning ¨ Table of Contents CM16a Amplifier Network Monitor Federal Communications Commission FCC Information Introduction- Overview Physical Characteristics Introduction- Physical Characteristics & LayoutIntroduction- Physical Layout Diagram Functional LISTING, Block Diagram & Detailed Descriptions Introduction- List of Functions & FeaturesIntroduction- Block Diagram part Introduction- Block Diagram part Introduction- Detailed Description of Functions Amplifier Monitoring Functions Introduction- Detailed Description of FunctionsRS-232 Port Functions Introduction- Network Description Introduction- Sample Network Topologies Introduction- Sample Network Topologies What is Included in the Carton Installation- Basics and MountingUnpacking Location ConsiderationsConnecting AC Power Installation- Mounting and AC PowerConnecting Audio Inputs Installation- ConnectionsConnecting the RLY/TRG Connecting page InputConnecting the RLY OUT Connecting the Monitor Chain OUTConnecting to Amplifiers Connecting to the RS-232 PortInstallation- Rear Panel Detail Installation- Hookup Example Operation- General Safe levels ANY time Bypass mode is usedThere are two distinctly different Bypass modes Operation- LED Behavior & Bypass Switch UsageUploading a new application file Tftp file transfer Operation- Bypass Switch UsageOperation- Serial Port I/O Interface Xon/Xoff Only Required for Attaching to Existing Networks IP Address AssignmentOperation- Telnet Access Fuse Replacement Operation- Fuse ReplacementSpecifications- Dimensions Specifications Input Signal ProcessingPower amplifier output processing Power amplifier management Control room foldback monitoringContact closure inputs and outputs Network Interface RS232 PortGeneral ARCHITECT’S and ENGINEER’S Specifications Ethernet Cabling Appendix- Ethernet Cable PinoutsAppendix- DataPort Pin-out & Connector P-N’s Pin Signal DescriptionDescription Encode Signals How to Contact QSC Audio Products
Related manuals
Manual 40 pages 47.09 Kb

CM16a specifications

The QSC Audio CM16a is a versatile and powerful amplifier designed to meet the demands of professional audio applications. Known for its reliability and performance, the CM16a is ideal for both live sound and installation scenarios, offering a perfect blend of advanced technology and user-friendly features.

One of the standout features of the CM16a is its Class D amplifier architecture. This technology ensures not only high efficiency but also a lightweight design, making it easier to transport and install in various settings. The amplifier delivers an impressive output power of 1600 watts at 4 ohms, providing ample headroom for demanding audio applications. The CM16a is capable of handling multiple speaker configurations, making it a flexible choice for various setups.

Another key characteristic of the QSC CM16a is its advanced thermal management system. This built-in feature ensures the amplifier operates within safe temperature limits, enhancing reliability and extending the lifespan of the unit. The CM16a also includes an intelligent protection circuit that safeguards the amplifier from overload and short circuits, allowing users to operate it confidently even during intense performances.

The CM16a comes equipped with multiple inputs and outputs, including XLR and TRS connectors, enabling seamless integration with a range of audio sources and systems. This versatility allows for easy connection to mixers, microphones, and instruments, making it suitable for diverse applications from concerts to corporate events.

In addition to its robust performance, the QSC CM16a features an intuitive front panel design with LED indicators for quick monitoring of system status and performance. Users can easily adjust levels and settings, ensuring optimal audio quality for any given situation.

The amplifier is also designed with efficiency in mind, incorporating Power Factor Correction (PFC) technology. This enhances power usage, reducing operational costs while minimizing environmental impact.

In conclusion, the QSC Audio CM16a stands out as a premier choice for audio professionals seeking a reliable, high-performance amplifier that can deliver exceptional sound quality. With its Class D technology, advanced protection features, versatile connectivity, and user-friendly design, the CM16a is a worthy investment for any audio application. Whether for live sound reinforcement or permanent installations, the CM16a promises to meet the needs of even the most demanding audio environments.