Product dimensions Before you start | Whirlpool 3191799 specification

Product dimensions

Before you start...

28-3/16" cooktop recessed width

28-5/32" oven recessed width

21" cooktop depth

24-13/32" to back of oven

31-11/16"

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will be

preceded by the safety alert symbol and the word “DANGER” or “WARNING”. These words mean:

You will be killed or

DANGER seriously injured if you

30-3/4"
recessed
height
from			31-1/2"
underside			overall
of cooktop			cooktop
of cooktop			width
to support			width
to support
slats


			shipping
			foot

23-1/8"

recessed

depth

30”overall height

30"

overall

width

don’t follow instructions.

You can be killed or

WARNING seriously injured if you don’t follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Have a qualified technician install this range.

Range location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Recessed installation area must provide complete enclosure around the recessed portion of the range.

Electrical ground is required. See “Electrical requirements.”

Cabinet opening dimensions

IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not

Countertop preparation:

Front edges: You may need to shave or cut the trim of formed or metal front-edged countertops to clear the 30" width of cooktop.

If countertop thickness is more than 1-1/2" inches thick: Countertop must be notched as shown to avoid damaging the oven control panel.

notch width to be equal both sides

1-1/2" max

30-1/8"

If countertop extends more

1-1/8" beyond cabinet front: Notch countertop as shown to clear oven control panel.

cabinet

notch widthfront to be equal

both sides

			1-1/8"


30-1/8"			max

discolor, delaminate or sustain other damage.

Range support surface MUST be solid, level and flush with bottom of cabinet cutout.

Do not seal range to side cabinets.

When installing a cooktop under existing cabinets and the installation does not meet the minimum cabinet clearances. Install a range hood above the cooktop to avoid burn hazards.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA

70 — latest edition**, and all local codes and ordinances.

	13" max. upper			1-1/2" max.
	13" max. upper			countertop
	cabinet depth			countertop
	cabinet depth			thickness

For minimum clearances to the top of cooktop see Note.*

wall

1-1/8"

19-5/8"

max.

25" countertop

depth

24" lower

cabinet

floor

cabinet depth

front

Top view of cabinet cutout

1/4"

radius both corners

30-3/4"

top of

countertop to support slats

Install a 3-1/2"-wide support slat on each side. Slats must be level front to back and with each other.

Mobile home installation

The installation of this range must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280); or when such standard is not applicable, the Standard for Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1/NFPA 501A, or with local codes.**

When this range is installed in mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Four-wire power supply cable must be used in a mobile home installation. The appliance wiring will need to be revised. See four-wire electrical connection, Page 3.

Tools needed:

1/2" dia.

Side view of cabinet cutout

router bitPhillips screwdriver

*Note: 24" min. when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper.

30" min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

Copies of the standards listed may be obtained from:

**National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

Top of countertop		28-1/2" min.
Top of countertop		28-1/2" min.
Note: countertop		opening width
must be level		28-5/8"
across front and		opening is
front to back.	recommended,
		if available.

Locate electrical	7/8" min.	30-3/4"
supply junction	required	top of	36" overall
box on cutout	between	counter-	36" overall
box on cutout	between	counter-	countertop
floor or on rear	cutout and	top to	height
wall (shown)	cabinet door	bottom	height
near floor line.	or hinge.	of cabinet
		cutout

Parts supplied:

2 screws

2 door removal pins

Front view of cabinet cutout

Page 1

3191799 specifications

The Whirlpool 3191799 is a highly regarded replacement part designed specifically for enhancing the functionality of various Whirlpool washing machine models. This component is primarily known as a water inlet valve assembly, which plays a critical role in the water supply system of the appliance. The effectiveness and efficiency of a washing machine heavily depend on the performance of this valve, making the Whirlpool 3191799 an essential part for maintenance and repairs.

One of the main features of the Whirlpool 3191799 is its robust construction, designed to withstand the rigors of daily use. It is built with high-quality materials that ensure durability and longevity, capable of withstanding varying pressure levels and extreme conditions. This ensures that users experience less frequent replacements, ultimately saving time and money over the lifespan of the washing machine.

The Whirlpool 3191799 specifically supports both hot and cold water functions. This dual capability allows for precise temperature control during wash cycles, catering to the needs of different fabrics and load types. With this inlet valve, users can expect enhanced washing performance, resulting in cleaner clothes and more effective stain removal.

Another technological advancement found in the Whirlpool 3191799 is its efficient design that simplifies installation. The product is designed to fit seamlessly with a variety of Whirlpool washing machine models, making it a versatile choice for many users. Clear instructions are typically provided, enabling even those with minimal DIY skills to replace the valve without professional assistance.

Additionally, the water inlet valve is equipped with advanced filtration features that help prevent the entry of debris or sediment into the washing machine. This not only protects the appliance from potential damage but also ensures that the quality of water used for washing remains pure and conducive to cleanliness.

In summary, the Whirlpool 3191799 water inlet valve assembly is an essential component for maintaining optimal washing machine functionality. With its durable construction, dual-temperature capability, ease of installation, and advanced filtration, this part stands out as a reliable choice for anyone looking to enhance their Whirlpool washing machine’s performance. Investing in this component can significantly contribute to the longevity and efficiency of laundry tasks, making it a smart addition to any home.