Attachment, Check operation | Whirlpool 3191799 guide

BElectrical connection

WARNING

Electrical Shock Hazard

Turn power supply off before connecting wires.

Use 8-gauge solid copper wire.

Electrically ground range.

Failure to follow these instructions can result in death, fire, or electrical shock.

This range is manufactured with white (neutral) power supply wire and a cabinet-connected bare

cable from

junction power supply box

	red	black
		wires
	wires

white wire

white and bare
ground range
cable wires —		U.L.-listed
factory crimped		U.L.-listed
factory crimped	cable from	conduit
Figure 1	cable from	conduit
Figure 1	range	connector

If local codes PERMIT

connecting cabinet-ground conductor to neutral white wire in junction box:

cable from

junction power supply box

	red	white
		wires
	wires

bare ground		black wires

wires
Figure 2		U.L.-listed
	cable from	conduit connector
	range
If local codes DO NOT PERMIT		If connecting to a
connecting cabinet-ground
conductor to neutral white		four-wire electrical system:
wire in junction box:

ground wire twisted together.

4. Make electrical connection following the steps needed for your installation.

1.Disconnect the power supply.

2.Remove the junction box cover.

3.Connect range cable to junction box through the U.L.-listed conduit connector.

4.Connect the two black wires together with twist-on connectors.

5.Connect the two red wires together with twist-on connectors.

6.Complete electrical connection according to local codes and ordinances.

7.Connect the factory-crimped bare and white range cable wires to the neutral (white) wire in junction box. See Figure 1.

8.Replace junction box cover.

7.Separate the factory-crimped bare and white range cable wires.

8.Connect white range cable wire to neutral (white) wire in junction box. See Figure 2.

9.Connect the bare ground range cable wire to a grounded wire in the junction box. See Figure 2.

10.Replace junction box cover.

7.Separate factory-crimped bare and white range cable wires.

8.Connect white range cable wire to neutral (white) wire in junction box. See Figure 2.

9.Connect the bare ground range cable wire to the green ground wire in junction box. Do Not connect bare ground wire to neutral (white) wire in junction box. See Figure 2.

10.Replace junction box cover.

CAttachment

Carefully push against seal area of range front frame when pushing range into cabinet.

Do Not push against outside edges.

5. Lift range into cabinet cutout using the oven opening as an area to grip. Be careful not to damage countertop.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Securely attach mounting screws to cabinet.

Reattach mounting screws if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

Slide top of trim up.

Push trim into place. Replace trim screw.

7. Slide top end of each trim upward onto range side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to range. Take care not to scratch other surfaces with ends of trim.

8. Replace oven racks.

oven frame hinge slot

shipping foot

To avoid damaging the countertop, lift range slightly while pushing against seal area of front frame. Push range into cabinet cutout until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet.

Push range completely into cabinet and center range in cabinet cutout. Be careful not to damage countertop.

2 screws

6. Important: Securely fasten range to cabinet using the two screws provided. Insert the screws through holes in mounting rails. Do Not overtighten screws.

door hinge

9. Replace the oven door by inserting ends of hinges into hinge slots in range frame. Push behind each hinge so that hinges are pushed into range frame as far as they will go. Open door and remove both door removal pins. Close and open door to check that door closes and opens completely. If door does not close or open completely, you have not pushed hinges completely into frame. Repeat door removal step and reinsert door into hinge slots again.

DCheck operation

10.Turn on power supply. The display panel will light up briefly. “PF” should appear in the temperature display.

11.Check the operation of the cooktop

elements. Push in and turn each surface unit control knob to “HI” position. Check the operation of the cooktop elements and indicator lights.

BAKE BROIL CLEAN

12.Check the operation of the oven

element. Press the “BROIL” pad. “BROIL” will appear in the display. Press the “START” pad. Make sure the oven door is closed and the “ON” light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the “CANCEL” pad. If your oven does not heat or an “F”, followed by a number, appears in the display, contact your dealer or check the “If you need service...” section of this Installation Instructions.

Page 3

3191799 specifications

The Whirlpool 3191799 is a highly regarded replacement part designed specifically for enhancing the functionality of various Whirlpool washing machine models. This component is primarily known as a water inlet valve assembly, which plays a critical role in the water supply system of the appliance. The effectiveness and efficiency of a washing machine heavily depend on the performance of this valve, making the Whirlpool 3191799 an essential part for maintenance and repairs.

One of the main features of the Whirlpool 3191799 is its robust construction, designed to withstand the rigors of daily use. It is built with high-quality materials that ensure durability and longevity, capable of withstanding varying pressure levels and extreme conditions. This ensures that users experience less frequent replacements, ultimately saving time and money over the lifespan of the washing machine.

The Whirlpool 3191799 specifically supports both hot and cold water functions. This dual capability allows for precise temperature control during wash cycles, catering to the needs of different fabrics and load types. With this inlet valve, users can expect enhanced washing performance, resulting in cleaner clothes and more effective stain removal.

Another technological advancement found in the Whirlpool 3191799 is its efficient design that simplifies installation. The product is designed to fit seamlessly with a variety of Whirlpool washing machine models, making it a versatile choice for many users. Clear instructions are typically provided, enabling even those with minimal DIY skills to replace the valve without professional assistance.

Additionally, the water inlet valve is equipped with advanced filtration features that help prevent the entry of debris or sediment into the washing machine. This not only protects the appliance from potential damage but also ensures that the quality of water used for washing remains pure and conducive to cleanliness.

In summary, the Whirlpool 3191799 water inlet valve assembly is an essential component for maintaining optimal washing machine functionality. With its durable construction, dual-temperature capability, ease of installation, and advanced filtration, this part stands out as a reliable choice for anyone looking to enhance their Whirlpool washing machine’s performance. Investing in this component can significantly contribute to the longevity and efficiency of laundry tasks, making it a smart addition to any home.