Whirlpool 9761893A Electrical Requirements, Gas Supply Requirements, Type of Gas, Gas Supply Line

Page 4

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

IMPORTANT: The cooktop must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

This cooktop is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.

This cooktop is equipped with an electronic ignition system that will not operate properly if plugged into a ground fault interrupt circuit.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120-volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

The wiring diagram are provided with this cooktop. See “Wiring Diagrams” section.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Leak testing of the range must be conducted according to the manufacturer’s instructions.

Type of Gas

Natural Gas:

This cooktop is listed by Underwriters Laboratories (UL/cUL) for use with Natural gas or, after proper conversion, for use with LP gas.

This cooktop is factory-set for use with Natural gas. To convert to LP gas, see the Gas Conversion instructions provided in the literature package. The model/serial rating plate located on the underside of the burner box has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See the Gas Conversion instructions provided in the package containing the literature.

Gas Supply Line

Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape. With LP gas, piping or tubing size can be ½" minimum. Usually, LP gas suppliers determine the size and materials used in the system.

4

Image 4
Contents Cooktop Safety 30 76,2 CM ET 36 91,4 CMInstallation Requirements Tools and PartsLocation Requirements Tools neededMobile Home Additional Installation Requirements Product DimensionsInstallation Clearances Gas and Electric Connection LocationsElectrical Requirements Gas Supply RequirementsType of Gas Gas Supply LineInstallation Instructions Prepare Cooktop for InstallationGas Supply Pressure Testing Gas Pressure RegulatorMake Gas Connection Install CooktopTo Assemble Pressure Regulator Complete Installation Typical flexible connectionComplete Connection If burners do not light properlyOn 30 76.2 cm models Wiring DiagramsOn 36 91.4 cm models Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteExigences demplacement Exigences DinstallationOutillage et pièces Spécifications électriques Dégagements de séparation à respecterType de gaz Spécifications de lalimentation en gazCanalisation de gaz Préparation de la table de cuisson pour Linstallation Instructions DinstallationInstallation de la table de cuisson Assemblage du détendeur Raccordement au gazRaccordement typique par raccord flexible Compléter le raccordement Achever linstallationSi le brûleur ne sallume pas correctement Schémas DE Câblage Sur les modèles de 30 76,2 cmSur les modèles de 36 91,4 cm 9761893A