Installation, Electrical requirements | Whirlpool 8285116 instruction

Electrical requirements

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure cooktop is properly grounded.

Do Not have a fuse in the neutral or grounding circuit.

The downdraft cooktop must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. The model/serial rating plate is located on the bottom of the cooktop.

A four-wire or three-wire, single-phase, 240-volt, 60-Hz, AC-only electrical

supply is required on a separate

30-ampere circuit, fused on both sides of the line.

A time-delay fuse or circuit breaker is recommended. The fuse size must not exceed the circuit rating of the appliance as specified on the model/serial rating plate.

CONNECT WITH COPPER WIRE ONLY.

Connected directly to the fused disconnect (or circuit breaker box) through flexible, armored or non- metallic sheathed, copper cable (with ground wire).

Flexible armored cable should connect cooktop directly to the junction box.

Fuse both sides of the line.

Locate the junction box to allow as much slack as possible between the junction box and cooktop so that the downdraft cooktop can be moved if servicing is ever necessary.

A twist-on connector and 1/2"

(12.7 mm) U.L.- or CSA-listed conduit connector must be provided at the junction box.

The recommended minimum copper wire size is No.-10 gauge. However, wire sizes and connections must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and 22.2

No. 0-M91 - latest edition** and all local codes and ordinances. Wire sizes and connections must conform with the rating of the cooktop.

Copies of the standard listed may be obtained from:

*National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

The wiring diagram is located on the bottom of the cooktop.

Twist-on connector and 1/2" (12.7 mm) U.L.- or CSA-listed conduit connector are not provided.

Installation

1. Remove shipping materials and tape from cooktop.

2. The blower is set to vent straight out the back of the cooktop.

To vent to the left side, right side or down through the bottom of the cabinet, add an elbow to the blower assembly exhaust vent.

It may be easier to connect appliance cable to junction box before inserting cooktop into cutout. See “Electrical connections,” Pages 6-8.

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop.

Failure to do so can result in back or other injury.

front edge of downdraft cooktop is at least 1-1/2" (38.1 mm) from front edge of countertop and parallel to countertop.

rear edge of cooktop is at least 3/4"

(19.1 mm) from rear wall as recommended.

side edge of cooktop is at least 6 inches (15.2 cm) from side wall.

4. Connect vent system. See “Venting requirements,” Pages 4-5. Use duct tape to seal all joints. Vent must end with a wall or roof cap outside the building.

Electrical connection

WARNING

This cooktop must be connected to a grounded, metallic permanent wiring system or a ground connector should be connected to the ground terminal or wire lead on the cooktop.

This cooktop is manufactured with a frame connected, green or bare ground wire. Connect the cooktop cable to the junction box through the 1/2" (12.7 mm) U.L.- or CSA-listed conduit connector. Complete electrical connection according to local codes and ordinances.

5.Make the electrical connection:

Lift entire cooktop up from cutout when positioning cooktop in countertop opening.

3. Insert downdraft cooktop into cutout. Check that:

cooktop is centered in cutout.

Electrical Shock Hazard

Turn power supply off before connecting wires.

Use 10-gauge solid copper wire. Electrically ground cooktop.

Failure to follow these instructions can result in death, fire, or electrical shock.

8285116 specifications

Whirlpool 8285116 is a premium refrigerator water filter designed to improve the quality of drinking water and ice produced by compatible refrigerators. With its advanced filtration technology, the filter is capable of removing contaminants, such as chlorine, lead, and other impurities, ensuring that you enjoy fresh-tasting water and ice.

One of the most notable features of the Whirlpool 8285116 is its NSF certification. This certification assures consumers that the filter meets rigorous standards for contaminant removal and overall performance. The filter is designed to reduce more than 99% of harmful substances, making it an essential accessory for health-conscious consumers.

Another significant aspect of the Whirlpool 8285116 is its easy installation process. Users can replace the filter without the need for additional tools. The quick-change design allows for a straightforward swap-out, making it convenient for anyone to maintain their refrigerator’s water filtration system. This ease of use extends the longevity of the filter, as regular replacements ensure optimal performance.

The Whirlpool 8285116 operates utilizing a carbon block filtration media. This technology is effective in reducing bad tastes and odors commonly associated with tap water. The carbon absorbs impurities, while the design also minimizes the potential for bacteria growth within the filter.

In terms of compatibility, the Whirlpool 8285116 is designed to fit a wide range of Whirlpool, KitchenAid, and Maytag refrigerators. Always ensure compatibility with your specific refrigerator model for optimal performance.

The filter should be replaced approximately every six months, depending on usage, water quality, and frequency of use. Regular replacement is crucial to ensure that the filtration system remains effective, providing clean water and ice for your family.

In summary, the Whirlpool 8285116 water filter offers a combination of reliability, performance, and ease of use. With its NSF certification, advanced carbon block technology, and user-friendly installation process, it stands out as an excellent choice for consumers looking to enhance their refrigerator's water quality. By investing in this filter, you can enjoy the benefits of clean, fresh water and ice, ensuring that your family's hydration needs are met with the highest standards in water purification.