Whirlpool RBD306 manual Frameto lift oven, Ovenracks, Supplycable, Shipping\ feet Replace ovendoor

ElectricalShock Hazard

Electrically ground oven.

Connect ground with lO-gauge-minimum solid copper wire.

Failure to follow these instructions could result in death, fire or electrical shock.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordancewith local codes.

i;iiiiiijij operation,

" I iii!iXiiiii!Check oven

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure oven is properly grounded.

Do Not have a fuse in the neutral or grounding circuit.

Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. (The model/serial rating plate is located on the oven door or on the oven frame.)

[] CONNECT WITH COPPERWIRE ONLY.

[] Models rated from 7.3 to 9.6 kW at 240 volts (5.5 to 7.2 kW at 208 volts) require a separate 40-ampere circuit. Models rated at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts) require a separate 30-ampere circuit.

1

[] A time-delay fuse or circuit breaker is recommended.

[] Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).

[] Flexible armored cable from appliance should be connected directly to junction box.

[] Fuse both sides of the line.

[] A U.L.-listed conduit connector must be provided at the junction box.

[] Do Not cut the conduit.

Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical Code,

ANSI/NFPA 70 -- latest edition (*, See Page 1) and all local codes and ordinances.

if! Oraspoven

frameto lift oven.

ii! "em°ve

ovenracks.

i!i:xi!Ipower

supplycable

Remove_v_

shipping\ feet.

Replace ovendoor.

re,aration

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to follow this instruction can result in back or other injury.

Important: Use both handsto remove oven doors.

Do Not use handle or any portion of the front frame or trim for lifting.

Beforemoving oven acrossfloor, checkthat oven is on shippingbase or slideoven onto cardboard or hardboard.

Do Not remove shippingfeet at the front lower corners of oven.

shippingfeet.

•Turn power supply off. Move oven close to final position.

•Remove and discard shipping materials, tape and protective film from the oven. Do Not remove shipping base or shipping feet at the front lower corners of oven. The shipping feet

will protect the lower oven trim until oven is inserted into cabinet.

•Remove and set aside racks and other parts from inside oven.

Use screws to attach
oven to cabinet.	Graspoven	Reattach side
		_leces.
Reattach side
	................................frameto lift
	oven.
Remove
trim screws.
		Remove side
Remove side		trim.

trim,

cabinet.

		Remove trim
		screws.
	................................supplycable	Remove
ili!iiii"em°ve	power \
		oven doors.
ovendoor.
	Remove
	shipping
	feet.
	Rep,ace
	................................ovendoors

Insert small

end of pin here.

_.Removetrim screw.

Pulltrim out.

Pull top of trim down.

•	Completely	open lower oven door. Insert	• Remove trim screws attaching right and
small	end of a door removal pin into each door		left side trim to oven. Grasp the bottom end of
hinge.	Grasp door	handle from the bottom and	trim and pull away from oven. Slide top end of
gently	close door	as far as it will shut. Lift slightly	trim downward to remove trim from oven. Take
and grasp bottom		of door with other hand. Pull	care not to scratch other surfaces with ends of
door out at bottom to remove. Set door aside on			trim. Set trim and screws aside on protected
protected surface.			surface.
Repeat for upper oven door.

Page 2