Whirlpool W10541636A Installation Instructions, Unpack the Ice Maker, Location Requirements

Page 2

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

INSTALLATION INSTRUCTIONS

Unpack the Ice Maker

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

■To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Ice Maker Care” section.

Location Requirements

■To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

■Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve or a Whirlpool supply line Part #8212547RB, and a Whirlpool approved drain pump, Part #1901A, only to carry the water to an existing drain.

■Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F and 90°F (21ºC and 32°C).

■The ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray, or drip.

■When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTES:

■Check that the power supply cord is not damaged, or pinched or kinked between the ice maker and the cabinet.

■Check that the water supply line is not damaged, or pinched or kinked between the ice maker and the cabinet.

■Check that the drain line (on some models) is not damaged, or pinched or kinked between the ice maker and the cabinet.

 

 

11¹⁄₂"

A

 

(29.2 cm)

34"

 

 

 

(86.4 cm)

 

 

 

Min.

 

 

28¹⁄₂"

34¹⁄₂"

 

 

(87.6 cm)

 

 

(72.4 cm)

Max.

3¹⁄₂"

9"

 

 

(22.9 cm)

 

 

(8.9 cm)

 

 

24"

 

B

 

 

 

 

(60.1 cm)

 

 

 

15"

 

 

(38.1 cm)

 

A. Recommended location for electrical and plumbing fixtures B. Floor level

■Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See “Leveling.”

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents ICE Maker Safety Table of Contents/Table des matièresUnpack the Ice Maker Installation InstructionsCleaning Before Use Location RequirementsVacation or Extended Time Without Use Electrical RequirementsWater Supply Requirements Connect Water SupplyKit Contains Ice Maker Drain Pump InstallationRear View Drain Cap If Ice Maker Is Currently InstalledDrain Pump Installation Water Supply LineDrain Pump Mounting Tab Slot Drain Pump InstalledParts Locations Vent TubeSide View Drain ConnectionGravity Drain System Drain Pump System on some modelsOn Some Models Connecting the DrainIce Maker Door Reversal-Side Swing Only Door Stop and End-Cap ReversalOn Some Models-Replace Door Wrap Reverse HingesReplace Door Top HingeInterior Components CleaningLeveling On Some Models Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteDéballage de la machine à glaçons Instructions D’INSTALLATIONExigences d’emplacement Spécifications électriquesRaccordement à la canalisation d’eau Spécifications de l’alimentation en eauVacances ou longue période d’inutilisation Contenu de l’ensemble Installation de la pompe de vidange de la Machine à glaçonsVue arrière Bouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Canalisation d’alimentation en eauTube de vidange Position des piècesVidange par gravité Raccordement au drain de vidangeTube de ventilation Vue latéraleSystème avec pompe de vidange sur certains modèles Raccordement du drain de vidangeInversion du sens de montage des charnières Réinstallation de la porteSur certains modèles Réinstallation du revêtement de porte Charnière supérieureCharnière inférieure Inversion du sens dinstallation de la gâche de porteNivellement Nettoyage Composants intérieursSur certains modèles Imprimé aux É.-U

W10541636A specifications

The Whirlpool W10541636A is a top-tier refrigerator model designed to meet the needs of modern households while providing optimal cooling performance and energy efficiency. This appliance stands out due to its innovative features and advanced technologies that cater to the demands of contemporary living.

One of the main features of the W10541636A is its spacious interior, offering ample storage capacity for all types of food and beverages. The refrigerator is designed with adjustable shelving that allows users to customize the layout according to their needs. The clear drawers make it easy to access vegetables and fruits while maintaining freshness. Furthermore, the sleek design includes door bins that can accommodate large gallon containers, maximizing storage efficiency.

A standout characteristic of this refrigerator is its advanced cooling system. The W10541636A employs Whirlpool's Precision Temperature Control technology, which ensures that food stays at the ideal temperature, reducing spoilage and maintaining flavors. The multi-airflow system distributes cold air more evenly throughout the refrigerator, minimizing temperature fluctuations and ensuring that every shelf remains consistently cool.

Energy efficiency is another key attribute of the W10541636A. It is designed to operate with reduced energy consumption, helping households save on utility bills while being environmentally friendly. This model is ENERGY STAR certified, indicating that it meets strict energy efficiency guidelines set by the EPA.

In terms of convenience, the Whirlpool W10541636A includes features such as an external water and ice dispenser, providing quick access to chilled water and ice without having to open the refrigerator door. The intuitive controls and LED lighting enhance usability, allowing for easy customization of temperature settings and improved visibility, making it effortless to find items inside.

In conclusion, the Whirlpool W10541636A refrigerator combines innovative features, advanced cooling technologies, and energy efficiency to provide consumers with a quality appliance suited for busy lifestyles. Its spacious design, precision cooling systems, and user-friendly characteristics make it a reliable choice for families seeking both functionality and style in their kitchen. Whether storing fresh produce, prepared meals, or beverages, the W10541636A delivers performance that enhances everyday living.
Top Page Image Contents