Whirlpool DP6000XR Series manual Problem

PROBLEM

Dishes not washing clean

Cloudy film on glassware, etching - permanent corrosion

Dishes 81 lnterlor of dlshwasher yellow or brown

Bust spots on stalnless steel -OR-

Dark spots on tlatware - stalnless steel, sliver plate, or sterling

Bronze tarntsh on sllverplate

CAUSED BY

Water is not hot enough

Improper loadrng

Spray arm or arms not rotating freely

Not enough detergent or improper

detergent

“0ld”detergent.

Water pressure may

be low, dishwasher is not fillina -.oroperlv

Too much detergent in soft water

Inadequate rinsing

Iron or manganese in water

Allowing salty or acidic foods such as

mayonnaise. vinegar, fruit juices, salad dressings, milk products to remain on flatware.

Undissolved

detergent coming in contact wrth flatware

Silverplate is worn off Exposed base metal to kes on a bronzed hue.

SOLUTION

Water temoerature should be at least 140°F fbO”C1. Set water heater thermostat to a hrgher setting. Run water at

sink until hot before starting and/or use HI-TEMP WASH Option.

Make sure dishes and glassware are loaded so spray

reaches all surfaces and items drain properly Do not ov- erload Do not nest items

Make sure large items do not block spray from reaching detergent dispensers.

Check spray arms to make sure they turn freely after load- ing. Be sure a utensil has not prevented their turning.

Use more dishwasher detergent. Use detergent with high-

est available phosphorus content...especially with hard water.

Use only fresh dishwasher detergent. Store tightly closed container, in cool, dry place. Discard old detergent. Do not fill dispensers until ready to start dishwasher.

If water pressure is low, do not use water for other purposes while dishwasher is running (to assure correct fills).

Check for rarnbow hue on glasses. A rainbow hue is the first sign of etchrng (corrosion of glass]. Reduce the amount

of dishwasher detergent. Use a detergent with a lower phosphorus content.

If water pressure is low do not use water for other purposes

while dishwasher is running [to assure correct water fills]. Make sure dishes and glassware are loaded properly to

assure adequate rinsing and drarning. Do not overload.

Temporary remedy:

1 Set empty dishwasher for a “one wash” cycle.

2.Start dishwasher and unlatch door to stop it when it has filled for the wash part of the cycle.

3.Add ‘/4 to :i cup (120 to 240 ml) of citric acid crystals

(usually available in drugstores).

4 Close and latch door to complete cycle.

Permanent solution: Install an iron or manganese filter to home water supply

Rinse flatware that is to stand for several hours before washing (use Rinse & Hold). Clean stained items with silver polish and re-wash. Do not put stalnless steel and sliver

tlatware In the same sllverware basket compartment. Direct contact between these metals can cause perma- nent damage to the sliver.

Remove spots with silver polish. Avoid spilling concentrated detergent on wet flatware.

Remove tarnish with silver poltsh. Have silver replated.

Water	left in	Drshwasher	cycle	not
bottom	ot	completed
dishwasher		Clogged	drain	air

gap

Allow dishwasher to complete cycle

Some plumbing codes require use of a drain air gap be-

tween an undercounter dishwasher and the drain system of the house The air gap is usually located above the sink or on the top of the counter near the dishwasher to prevent the possibility of water backing up from the drain into the

dishwasher due to a plugged drain. The drain air gap is

NOT a part of the dishwasher and is NOT covered by the

dishwasher warranty. The drain air gap should be kept clean to insure proper draining of the dishwasher.