Display
Style 1 - Electronic Oven Control
When power is first supplied to the appliance, “12:00 PM” will appear on the display. See “Clock” section to set time of day.
If “12:00 PM” appears at any other time, a power failure has occurred. Press OFF/CANCEL and reset the clock if needed.
When the oven is not in use, the display shows the time of day.
Styles 2, 3 & 4 - Electronic Oven Controls
When power is first supplied to the appliance, “PF” or a flashing time will appear on the display. Press OFF/CANCEL to clear the display.
If “PF” or a flashing time appears at any other time, a power failure has occurred. Press OFF/CANCEL and reset the clock if needed.
When the oven is not in use, the display shows the time of day.
When performing a timed cook function, the display will show either hours and minutes, or minutes and seconds.
Start
Style 1 - Electronic Oven Control
The Start pad begins any oven function. The display will show
SET TEMP OR TIME OR PUSH START.
Styles 2, 3 & 4 - Electronic Oven Controls
The Start pad begins any oven function. If the Start pad is not pressed within 5 seconds after pressing a function pad, the “START?” or “?” indicator light will appear on the display (on some models).
If the Start pad is not pressed within 5 minutes after pressing a function pad, the oven display will return to the time of day mode and the programmed function will be canceled.
Off/Cancel
The Off/Cancel pad stops any function except the Clock, Timer, Control Lock or Warm Drawer (on some models).
Clock
On some models, this is a
To Set:
Before setting, make sure the oven and Timer are off.
1.Press CLOCK.
2.Depending on your model, press the HR or MIN or TIME/ TEMP “up” or “down” arrow pads to set the time of day, including a.m. or p.m.
3.Press CLOCK.
Tones
Tones are audible signals, indicating the following:
Basic Functions
One tone
■Valid pad press
■Oven is preheating (long tone)
■Function has been entered
■Reminder (on some models), repeating each minute after the
Three tones
■Invalid pad press
Four tones
■End of cycle
Style 1 - Electronic Oven Control
Reminder Tones: Reminder tones may be turned off. On some models, press and hold BAKE for 5 seconds. REMINDER TONES OFF will appear on the display. Repeat to turn reminder tones back on, and REMINDER TONES ON will appear on the display.
All Tones: All of the above tones are preset on.
To disable tones, press and hold CLOCK for 5 seconds. Repeat to turn tones back on.
To Turn Off/On: Press and hold CLOCK for 5 seconds. A tone will sound when changing tones from OFF to ON. ALL SOUNDS OFF will appear on the display. Repeat to turn tones on, and ALL SOUNDS ON will appear on the display.
Tone Pitch: The pitch is preset at high, but can be changed to low.
To Change: Press and hold BROIL for 5 seconds. A tone will sound, and TONE PITCH LOW will appear on the display. Repeat to change and TONE PITCH HIGH will appear on display.
End of Cycle Tones: Press and hold CONVECT for 5 seconds to turn END OF CYCLE TONES off. Press and hold CONVECT for 5 seconds to turn END OF CYCLE TONES on.
Key Press Tone: Press and hold WARM (Cooking Options) for 5 seconds, and KEY PRESS TONES OFF will appear on the display. Press and hold WARM for 5 seconds, and KEY PRESS TONES ON will appear on the display.
Style 2 - Electronic Oven Control
Reminder Tones: Reminder tones may be turned off. On some models, press and hold TIMER SET for 5 seconds. “rEP OFF” or “OFF” will appear in the display. Repeat to turn reminder tones back on, and “rEP ON” or “ON” will appear in the display.
All Tones: All of the above tones are preset on. All except the
To Turn Off/On: Press and hold STOP TIME for 5 seconds. A tone will sound, and “Snd OFF” will appear on the display. Press and hold COOK TIME for 5 seconds to turn tones on, and “Snd ON” will appear on the display.
Tone Pitch: The pitch is preset at high, but can be changed to low.
To Change: Press and hold DELAY START for 5 seconds. A tone will sound, and “Snd LO” will appear on the display. Repeat to change, and “Snd HI” will appear on display.
Style 3 & 4 - Electronic Oven Control
Refer to Basic Functions in the “Tones” section.
12