finished installing your new Whirlpool ranae. To aet the most efficient use from your new
range, read your Whirlpool Use&Care
Congratulations!
Guide. Keep Installation Instructions and Guide close to range for easy
hreference. The instructions will make reinstalling your Whirlpool
LX Gas
Conversion
(Electronic Ignition and Standing Pilot Systems)
Converttng | to L.P. gos | Nahml |
should be | done by |
|
a quaffled | Installer. |
|
Only a qualified A installer should
n Install or adjust your gas range.
Pressure Regulator: Use a wrench to unscrew the COD from
the top by turning counter-
clockwii. Turn the cap over so the hole end is up. Replace the cop and gasket on the regutator. DO NOT REMOVE THE PRESSURE REGULATOR.
Part No. 76724.CQ/4320880
01990 Whirlpool Corporation
|
|
|
|
|
|
|
|
|
| C | Oven | Burner: | Remove | oven | ’ | ||||||
|
|
|
|
|
|
|
|
|
| racks | and | lower | panel | from |
| ||||||
|
|
|
|
|
|
|
|
|
| oventottom. |
| Turn | the orifice | hood |
| ||||||
|
|
|
|
|
|
|
|
|
| down until snug against pin. DO NOT |
| ||||||||||
Burners: |
|
|
|
|
|
|
|
| OVERTIGHTEN. The burner flame should |
| |||||||||||
|
|
|
|
|
|
|
| be | l/2’ | long | when |
| air | shutter | is correctly |
| |||||
Turn the orifices |
|
|
|
|
|
| adjusted | The | air | shutter | slides | to | close | or | |||||||
hood | down |
| until | snug |
|
|
|
|
| open the shutter | OS needed. | See Pane |
| ||||||||
against | pin. | DO | NOT | OVERTIGHTEN. |
| C, | Step | 21 for electronic |
| ignition | systems, |
| |||||||||
Adjust | the | air | shutters | for proper | flame | by | or | Step | 23A | for | standing |
| pilot | systems. |
| ||||||
sliding | the | air | shutter | to | close | or | open | the | Replace | oven | bottom | ond rocks. |
|
| |||||||
shutter | as | needed. | See | Panel | C, Step | 18 |
|
|
|
|
|
|
|
|
|
|
|
| |||
for electricul |
| lgtition | systems | or | Step 19P |
|
|
|
|
|
|
|
|
|
|
|
| ||||
for standing |
| pllot | systems. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| D. | Oven | thermostal: |
| Remove |
|
| ||||
|
|
|
|
|
|
|
|
|
| thermostat | knob. | pulling | straight | |||||||
|
|
|
|
|
|
|
|
|
| off. | Use a small | screwdriver |
| to rotate | the | |||||
|
|
|
|
|
|
|
|
|
| key | to | L.P. Replace thermostat | knob. |
| ||||||
Caoktop | burners | with | standing |
| pilots |
|
|
|
|
|
|
|
|
|
|
|
| |||
require |
| adjustment | of | pilot | flame | to | l/4’ |
|
| After | all | the | burners | have | been | |||||
hlgh. | The adjustment | control | is located | E converted |
| to L.P. gas usage | and | |||||||||||||
on the |
| manifold | plpe | or | at | pilot | ftame |
|
| |||||||||||
base, | depending | on the | model, |
|
| gas~ne | is connected, | check | for leaks. |
| ||||||||||
|
| Use | a | brush and | liquid detergent | to test | ||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| all gas | connections | for | leaks. | Bubbles |
| |||||
|
|
|
|
|
|
|
|
|
| around | connections | will | indicate | a |
| |||||
|
|
|
|
|
|
|
|
|
| leak. If a leak appears, shut off gas |
| |||||||||
|
|
|
|
|
|
|
|
|
| valve controls and |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| connections. | Then | check | connections |
| ||||||
|
|
|
|
|
| CORPORAllON |
|
|
| LEAKS WITH | ||||||||||
TKifl |
|
|
|
|
| 01 | ogoln. | NEVER TEST FOR GAS | ||||||||||||
|
|
|
|
| MATCH | OTHER FLAME. |
|
|
| |||||||||||
|
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Prepared by Whirlpool | Corporation. | Benton | Harbor. | Michigan | 49022 |
|
|
|
|
|
|
| Printed | in | U.S.A | |||||