Whirlpool 8053365 Electronic ignition system, Check operation of cooktop

Page 6
H HIG

ECheck operation

Electronic ignition system

Cooktop and oven burners use electronic ignitors in place of standing pilots. When a cooktop control knob is turned to the “LIGHT” position, the system creates a spark to light the burner. This sparking continues until the control knob is turned to the desired setting.

When the oven control is turned to the desired setting, a hot surface ignitor heats to a bright orange and ignites the gas. No sparking occurs and the glow bar remains on while the burner operates.

Check operation of cooktop

O

F

F

L

I

G

H

T

15.Push in and turn each surface unit control knob to “LIGHT” position. The flame should light within 4 seconds. Turn control knob to “HIGH” position after burner lights.

Check each cooktop burner for proper flame. The small inner cone should have a very distinct blue flame 1/4" to 1/2" long. The outer cone is not as distinct as the inner

cone. If the flame is noisy or blowing, it is getting too much air. If the flame is soft and lazy, it is not getting enough air. Turn surface burner control knobs to “OFF” position. Adjust air shutter if needed.

If surface burners need adjusting:

1.Remove control knobs. Do Not use a metal blade to pry off control knob; this could damage the product. If the control knob cannot be easily removed, tuck a cloth under the knob and pull out on the cloth with steady, even pressure to remove the knob.

2.Open oven door and remove 3 screws from bottom of manifold panel. Pull down slightly on manifold panel and pull panel away from range.

Check operation of oven burner

17.Open broiler drawer. Follow the instructions for your type of oven controls.

If your oven has this type of electronic control pads (with or without timer):

ON

BAKE

BROIL

PREHEAT

START ? 888

 

CUSTOM

TEMP/

START

OFF

BAKE

BROIL

TEMP

 

 

TIME

ENTER

CANCEL

 

 

 

5 SEC

 

A

TIMERON

BAKE

BROIL

START ? 888

HEAT

BAKE

CUSTOM

TEMP/

CLOCK

START

OFF

BROIL

TEMP

TEMP

ENTER

CANCEL

 

TIME

TIMER

 

 

 

 

5 SEC

 

B

1.Press the “BAKE” pad.

The “BAKE” indicator will light.

“350” will appear in the display.

2.Press the START/ENTER pad.

The “PREHEAT” or “HEAT,” and “ON” indicators will appear.

The display will show the automatic countdown time (10 minutes) needed to preheat the oven for selected temperature.

The oven burner should light in 50-60 seconds; this delay is normal. The oven valve requires a certain time before it will open and allow gas to flow.

If your oven has this type of electronic control pads:

 

 

888°F

ON 88:88

 

 

 

 

 

 

HEAT BAKE BROIL

 

 

TIMER

 

 

 

 

 

 

 

 

TIMER

 

 

 

START

OFF

BAKE

CUSTOM

TEMP

CLOCK

SET

LIGHT

HR

MIN

TIMER

ENTER

CANCEL

 

BROIL

 

 

 

 

 

 

 

 

 

 

 

OFF

 

 

 

5 SEC

 

To avoid damaging the hot surface ignitor, Do Not insert any object into the openings of the protective shield that surrounds the ignitor or clean that area.

18.Check the oven burner for proper flame. The flame should be 1/2" long, with inner cone of bluish- green, and outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or

lifting of flame should occur. If burner does not light, check that the regulator shutoff valve is in the “on” position (see Step 11).

regulator

shutoff valveair shutter and screw

If oven flame needs adjusting:

Locate the air shutter next to the pressure regulator. Loosen screw and adjust the air shutter until the proper flame appears. Tighten screw.

19.Turn the control knob to “OFF” or press the “OFF/CANCEL” pad.

Check operation of broil burner

20.Broil burner and oven burner are the same burner. Follow the instructions for your type of oven controls.

If your oven has this type of electronic control pads (with and without timer):

ON

BAKE

BROIL

PREHEAT

START ? 888

air shutter

3.Using a flat-blade screwdriver, adjust the air shutter for each burner as needed. Close the air shutter to decrease the amount of air to the flame. Open the air shutter to increase the amount of air to the flame. Adjust the air shutter to the widest opening that will not cause the flame to lift or blow off of the burner.

4.Repeat the first part of Step 15 after adjusting the air shutters.

5.Replace manifold panel by tightening 3 screws in bottom of manifold panel.

6.Replace control knobs on valve stems.

16.Push in and turn each cooktop control knob from “LIGHT” to “LOW” setting quickly. The low flame should be a minimum, steady blue flame.

If flame needs to be adjusted, turn control knob to the “LOW” setting and remove control knob. Insert a small flat-blade screwdriver into the valve stem. Turn the valve screw to obtain the smallest flame that will not go out when the control of a cold burner is quickly turned from “HIGH” to “LOW”. Repeat for other cooktop burners as needed.

C

1.Press the “BAKE” pad.

The “BAKE” indicator will light.

“350°F” will appear in the display.

2.Press the START/ENTER pad.

“PrE,” and “10:00” will appear in the display.

“HEAT” and “ON” indicators will light.

 

CUSTOM

TEMP/

START

OFF

BAKE

BROIL

TEMP

 

 

TIME

ENTER

CANCEL

 

 

 

5 SEC

 

A

TIMERON

BAKE

BROIL

START ? 888

HEAT

BAKE

CUSTOM

TEMP/

CLOCK

START

OFF

BROIL

TEMP

TEMP

ENTER

CANCEL

 

TIME

TIMER

 

 

 

 

5 SEC

 

B

1.Press the “CUSTOM BROIL” pad.

“525” or “HI” will appear in the display.

The “BROIL” indicator will light.

2.Press the “START/ENTER” pad.

“HEAT”(console B only) and “ON” indicators will light.

The oven burner should light in 50-60 seconds; this delay is normal. The oven valve requires a certain time before it will open and allow gas to flow.

Page 6

Image 6
Contents Table of Contents If you need assistancePages Before you start Product dimensionsCabinet dimensions/requirements Parts suppliedGas supply requirements Conversion must be done by a qualified service technicianTools needed Electrical requirements Natural GASPreparation Installation stepsAnti-tip bracket installation Anti-tip bracket must be anchored securely to the sub floorGas and electrical connections All connections must be wrench-tightenedRegulator shutoff valve On position Check operation of cooktop Check operationElectronic ignition system Check operation of oven burnerDo not Remove the Pressure Regulator Gas conversionsGas conversion Electrode Screws Burner base Cap Natural Plastic PressureCooktop burners Pull range out from countertop front about YOU Must Adjust LOW Setting for Each Cooktop Burner AS in ,Natural gas conversion Natural GasMoving the range If you need serviceIf you need assistance Range foot

8053365 specifications

The Whirlpool 8053365 is a high-quality refrigerator water filter that has become increasingly popular among homeowners aiming to enhance their drinking water quality. Known for its efficient design and reliable performance, this water filter is engineered to reduce various impurities, ensuring that the water you consume is both safe and tasty.

One of the main features of the Whirlpool 8053365 is its ability to eliminate common contaminants found in tap water. This includes chlorine, sediment, and other impurities that might affect the taste and odor of your drinking water. By using advanced filtration technology, this water filter can remove up to 99% of various harmful substances, making it an excellent choice for health-conscious consumers.

The filter is easy to install, requiring no specialized tools or professional assistance. It connects seamlessly with compatible Whirlpool refrigerators, allowing homeowners to enjoy clean water and ice effortlessly. The quick connect design allows for hassle-free replacement, ensuring that users maintain fresh filtration without complicating their routine.

In terms of longevity, the Whirlpool 8053365 boasts an impressive lifespan, typically lasting up to six months or 200 gallons of water. This durability makes it an economical option for families and individuals who rely on consistent access to purified water. Regular replacement of the filter is essential to ensure optimal performance and to maintain water quality over time.

Another important characteristic of the Whirlpool 8053365 is its certification. This filter meets rigorous standards set forth by the NSF International, an independent organization that certifies water filtration products. This certification gives consumers peace of mind, knowing their filter has been tested for effectiveness and safety.

Overall, the Whirlpool 8053365 is a well-designed water filter that combines efficiency, durability, and ease of use. With its ability to improve water quality and compatibility with various Whirlpool refrigerator models, it remains a go-to choice for homeowners looking for a dependable water filtration solution. Whether for drinking water or ice production, this filter stands out as a practical investment in better health and quality of life.