Broan Model E662 installation instructions Operation, Touch this touch pad to turn off lighting

12.OPERATION

Always turn your blower on before you begin cooking to establish an air flow in the kitchen. Allow the blower run for a few minutes to clear the air after you turn off the range.

HC0017 A B C D E F

A) Blower OFF Delay touch pad	D) OFF lighting touch pad
B) ON / Blower speed touch pad	E) Halogen light touch pad
C) OFF Blower touch pad	F) Nightlight / keyboard lock touch pad

A. BLOWER OFF DELAY TOUCH PAD:

When a speed is selected, touch the delay touch pad to activate the delay function. The corresponding speed indicator LED will start flashing to indicate this function is activated. Touch once for a 5-minute delay, twice for 10-minute delay, three times for 15-minute delay and four times for a 20-minute delay. The fan will continue to operate for the programmed minutes and will stop automatically. To cancel the delay function, wait 2 seconds and touch the delay touch pad once again; the blower will then work in normal mode.

NOTE: The blower speed can be increased - or decreased - during delay mode without starting another delay cycle.

B. ON /BLOWER SPEED CONTROL TOUCH PAD:

Touch this touch pad to turn on the blower at the last selected speed. To change the blower speed, touch the touch pad again until the desired speed is obtained.

NOTES: 1. Each time you touch on the speed control touch pad, the speed changes by increments of 1 (e.g.: speed

1 to speed 2, to speed 3, and then speed 4. From the fourth speed, goes down to speed 1).

2.The last speed used is kept in memory except the fourth, the next time the blower will be turned on, it will run on speed 3.

HEAT SENTRY

This hood is equipped with a Heat Sentry thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface.

1)If blower is OFF - it turns blower ON to HIGH speed.

2)If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.

When HEAT SENTRY is activated, the first and the last speed blower LEDs are flashing alternately. When the temperature level drops to normal, the blower will return to its original setting.

!WARNING

The HEAT SENTRY can start the blower even if the hood is turned OFF. In this case, it is impossible to turn the blower OFF with blower switch. If you must stop the blower, do it from the main electrical panel.

C. OFF BLOWER TOUCH PAD:

Touch this touch pad to turn off the blower.This command also cancels the delay function (if activated).

D. OFF LIGHTING TOUCH PAD:

Touch this touch pad to turn off lighting.

E. HALOGEN LIGHT TOUCH PAD:

Touch this touch pad to turn on the halogen lamps. The lighting intensity changes by increments of 1 (e.g.: Touch once for low intensity, once again to get more, up to three times. From the higher intensity, touch once to go back to the lower intensity).

NOTE: The last lighting intensity used is kept in memory. The next time the halogen lamps will be turned on, they will light with the last intensity used.

F. NIGHTLIGHT / KEYBOARD LOCK TOUCH PAD:

Touch this touch pad to activate the nightlight. The LED will light to indicate the nightlight is on.

When cleaning the hood, use the keyboard lock. To activate the keyboard lock, touch on this touch pad during 3 seconds; the LED will flash to indicate the keyboard lock is on. Touch on the touch pad and hold for 3 seconds again to stop the keyboard lock function.

NOTES: 1. When cleaning the hood, never spray cleaning agent directly on the controls; spray it on the cleaning cloth and wipe the control with it. Spraying cleaning agent directly on the control will cause unexpected keyboard activation.

2.When the keyboard lock is on, it stops the HEAT SENTRY.

3.If there a temporary power failure when the keyboard lock is on, when the power will be restored, the keyboard lock will still be on.

- 9 -