Installing your Cooker Hood, Thermal CUT-OUT

Installing your Cooker Hood

SAFETY WARNINGS: THIS COOKER HOOD IS DESIGNED FOR DOMESTIC USE ONLY.

When installed above a cooking appliance, the distance between the surface of the hob elements and the lower grille of the chimney hood must be as follows:

Minimum 650mm - over an electric hob. Minimum 700mm - over a gas or mixed fuel

hob.

This chimney hood is not suitable for installation above a cooking appliance with a high level grill.

THERMAL CUT-OUT:

The fan motor of this appliance incorporates a thermal cut-out device which will operate if the hood is installed below the minimum recommended heights listed above, or if the motor becomes overheated. If the cut-out device is activated, switch off the fan motor and allow the hood to cool.

The cut-out device will reset itself when the fan motor has cooled significantly.

NOTE: This hood has been designed and approved for installation over an electric hob with a maximum input of 7kW or a gas hob with a maximum input of 10kW when fitted in accordance with the heights recommended above.

Your Cooker Hood can be installed either for recirculation or extraction through an outside wall.

When used in the extraction mode the Cooker Hood ducting must not be connected to a flue which is used for exhausting fumes from a central heating flue or water heating flue.

IMPORTANT: The exhaust air must not be expelled through a smoke or waste-gas chimney which is in use or through a shaft used for ventilating rooms or into the cavity of a cavity wall or into a cupboard above the cooker hood.

If the room contains, a flued fuel burning appliance, such as a gas or oil fired central heating boiler which is not of the ‘Balanced Flue’ type, you should make sure that there is adequate air inlet into the room at all times, so that fumes from the boiler are not drawn back into the room by the Cooker Hood.

NOTE: All installations must comply with local authorities and building regulation requirements for the discharge of exhaust air into the atmosphere.

All the fittings are supplied. If the hood is to be installed onto a hollow construction or plaster board wall, then special fixings will have to be purchased.

Before drilling, care should be taken to check for electric cables, water pipes or gas pipes on the wall to which the cabinet/canopy is to be fitted.

If the hood can only be fixed to a hollow construction plaster or partition board structure, then the wall must be sufficiently reinforced to be quite rigid in the area of the mounting brackets.

To avoid the risk of accidents when fitting the canopy and chimney to the wall please read and follow the installation instructions.

For ease of installation proceed as follows:

1.Fix the wall brackets.

2.Fix the canopy hood.

3.Connect the hood to the mains supply ensuring that the canopy is functioning correctly.

4.Select the type of installation, ie. ducting or recirculation.

5.Fix the chimney stack.

NOTE: The hood is more efficient in the exhaust mode, therefore, this position should be selected during the warmer months of the year when no heating is being used. When the room is being heated, if the recycle position is selected heat will not be wasted.

CRC60 specifications

The Creda CRC60 is a highly versatile and efficient cooker that appeals to both home cooks and culinary enthusiasts. Designed with practicality and innovation in mind, the CRC60 meets a variety of cooking needs, making it a staple in many modern kitchens. Here’s an overview of its main features, technologies, and characteristics.

At the heart of the Creda CRC60 is its powerful oven, which offers an impressive capacity, making it suitable for everything from simple weeknight meals to elaborate dinner parties. The appliance includes multiple cooking functions, such as fan-assisted, conventional, and grill settings, allowing users to achieve optimal results for any dish. With a robust temperature range, the oven can accommodate various cooking styles, ensuring flexibility in meal preparation.

One notable feature of the CRC60 is its advanced heat distribution technology. It utilizes fan-assisted heating to ensure even cooking, eliminating hot spots and allowing for consistent results across all levels of the oven. This technology not only enhances cooking efficiency but also significantly reduces cooking times, making it an ideal choice for busy households.

The external design of the CRC60 is both stylish and functional. Featuring a modern finish and a user-friendly control panel, it easily integrates into any kitchen décor. The appliance is equipped with high-quality knobs and an LCD display for intuitive operation. Safety is also a priority, and the CRC60 includes features such as a cooling fan and a double-glazed oven door, which minimizes the risk of burns while cooking.

Another standout aspect of the Creda CRC60 is its energy efficiency. Built to conform to modern energy standards, the appliance minimizes energy consumption without sacrificing performance. It provides an eco-friendly cooking solution that can lead to savings on energy bills.

Cleaning the Creda CRC60 is made easy with its easy-to-clean enamel interior, which helps prevent food residue from sticking. Additionally, some models come with a self-cleaning option, making maintenance hassle-free for the user.

In summary, the Creda CRC60 combines functionality, style, and efficiency, offering a wide range of features designed to elevate the cooking experience. Its robust performance, thoughtful design, and energy-saving technologies make it a valuable addition to any kitchen, catering to both everyday cooking needs and special occasion meals. With the Creda CRC60, users can enjoy the benefits of modern cooking technology while creating delicious dishes with ease.