Burner Adjustment, Appliance Electric Connection

TABLE N°1: Adaption to various types of gas						APPLIANCE CATEGORY:			II2H3+
Burner	Types of Gas		Pressure	Nozzle		Rater Capacity			Reduced		by-pass
				Diameter					Capacity		Diameter
			mbar	1/100 mm.	g/h	l/h	kw	kcal/h	kw	kcal/h	1/100 mm.
	Natural	G20	20	72	-	95	1	860	0,48	413	34 reg.
Auxiliary	Butane	G30	30	50	73	-	1	860	0,48	413	34
	Propane G31		37	50	71	-	1	860	0,48	413	34
	Natural	G20	20	97	-	167	1,75	1505	0,6	516	36 reg.
Semi-Rapid	Butane G30		30	65	127	-	1,75	1505	0,6	516	36
	Propane G31		37	65	125	-	1,75	1505	0,6	516	36
	Natural	G20	20	115	-	286	3	2580	1,05	903	52 reg.
Rapid	Butane	G30	30	85	218	-	3	2580	1,05	903	52
	Propane G31		37	85	214	-	3	2580	1,05	903	52
Dual	Natural	G20	20	72	-	95	1	860	0,48	413	34 reg.
Inner	Butane	G30	30	46	73	-	1	860	0,48	413	34
	Propane G31		37	46	71	-	1	860	0,48	413	34
Dual	Natural	G20	20	102	-	334	3,5	3010	1,8	1548	65 reg.
Outer	Butane	G30	30	66	254	-	3,5	3010	1,8	1548	65
	Propane G31		37	66	250	-	3,5	3010	1,8	1548	65
	Natural	G20	20	125	-	286	3	2580	1	860	48 reg.
Oven	Butane	G30	30	85	218	-	3	2580	1	860	48
	Propane G31		37	85	214	-	3	2580	1	860	48

BURNER ADJUSTMENT

1)Primary air adjustment:

Oven burner adjustment: follow the instructions below to adjust the primary air for the over burner:

1)Remove the oven bottom.

2)Loosen the screw P and adjust the position X of the Venturi cone (Fig. 15) according to the measurements indicated in table 2.

TABLE N°2: Burner primary air regulation (indicative)

Type of gas		BURNER
Type of gas		Oven (mm)
Natural	G20	fully open
Butane	G30	fully open
Propane	G31	fully open

2) Burner "MINIMUM" adjustment:

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1)Light the burner and set the knob to the MINIMUM position (small flame).

2)Remove the knob of the valve that is press fit on the rod of that valve.

3)If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole on the valve rod (Fig. 16) and turn the choke screw to the right or left until the burner flame is adjusted to minimum. If the cooker is equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see fig. 17).

4)Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1)Light the burner setting the knob to the MAXIMUM position.

2)Close the oven door and operate the oven for at least 10 minutes.

3)Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.

4)With a slotted screwdriver turn the choking screw (see figure 18) and, while observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position.

WARNING: The above-mentioned adjustment should be made only with methane gas burners, while for those operating with liquid gas the screw must be locked at the end in a clockwise direction. The grill burner always operates at maximum and therefore no minimum adjustment is required.

APPLIANCE ELECTRIC CONNECTION:

The electric connection must comply with the current legal standards and regulations. Before making the connection, check that:

-The system electrical rating and the current outlets are adequate for the maximum power output of the appliance (see the label applied to the bottom of the casing).

-The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards and regulations. The company will not be responsible for the non-compliance with these instructions.

When the connection to the power supply network is made using an outlet:

-If the power cord is supplied without a plug, apply a standard plug that is suitable for the load indicated on the label. Connect the wires according to the diagram shown in FIG.19 and check that:

letter L (phase) = brown wire; letter N (neutral) = blue wire;

ground symbol = green-yellow wire;

APPLIANCE CATEGORY:

II2H3+