1A). The flange D, to which the air exhaust pipe is connected, and a plug B, used to shut off the unused air outlet, are both supplied with the product.
• This device may be installed in two different ways:
1.Fixing the hood to the lower part of the wall cabinet (Fig.2)
- Make 4 holes in the wall cabinet respecting the measurements indicated in figures 2 A-2 C.
- Position the hood underneath the wall cabinet and fix it into place using 4 screws (not supplied) suitable for the type of cabinet.
2.Fixing the hood to the wall (Fig.2).
-Make4holesinthewallcabinetreferring tothemeasurements indicated in figures 2 A-2 B. - Hang the hood on the wall, using the2holesH,alignitinahorizontalpositionandfix itdefinitively to the wall using the two lower safety holes I (Fig. 2B). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be fixed.
The hood is already prepared for the version with which it was ordered. The versions may be:
-Extraction (Fig. 1A-3)
-Filter (Fig. 1B-4-7).
-If the hood is an extractor model, the lever C must be posi- tioned as indicated in Fig. 3.
-If the hood is a filtermodel, the lever C must be positioned as indicated in Fig. 4.
•Extractor version
The appliance expels the fumes through an outside wall or a duct. It is necessary to buy a telescopic pipe in accordance with the standards in use (inflammable) and connect it to flange D (Fig 1A). The flange D is supplied with the product and should be fixed above the air outlet hole of the hood as indicated in Fig. 3.
• Filtering version
To transform an extractor hood version into a filter hood version, please inquire with your retailer about purchasing charcoal filters. The filters should be fitted to the extraction assembly inside the hood, by centring them and rotating them 90 degrees, until they click into place (Fig. 7). To do this, remove the grille D (Fig. 5). Close the air outlet opening with the plug B, as indicated in Fig. 4.
USE AND MAINTENANCE
•It is recommended to operate the appliance prior to cooking.
It is recommended to leave the appliance in operation for 15 minutes after cooking is terminated in order to completely eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by the regularity of the maintenance operations, in particular, the active carbon filter.
•The anti-grease filters capture the grease particles suspended in the air, and are therefore subject to clogging according to the frequency of the use of the appliance.
In order to prevent fire hazard, it is recommendable to clean the filter at a maximum of 2 months by carrying out the following
instructions:
-Remove the filters from the cooker hood and wash them in a solution of water and neutral liquid detergent, leaving to soak.
-Rinse thoroughly with warm water and leave to dry.
-The filters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several washes. This is not cause for customer complaint nor replacement of panels.
•The active carbon filters purify the air that is replaced in the environment. The filters are not washable nor re-useable and must be replaced at maximum every four months. The saturation of the active carbon filter depends on the frequency of use of the appliance, by the type of cooking and the regularity of cleaning the anti-grease filters.
•Clean the fan and other surfaces of the cooker hood regularly using a cloth moistened with denatured alcohol or non abrasive liquid detergent.
•The illumination installation is designed for use during cooking and not for prolonged general illumination of the environment. Prolonged use of the illumination installation notably reduces the duration of the bulb.
•Replacing the acrylic or metal panels
To replace the acrylic or metal panels you need to first remove the grille D by pushing the two side buttons B inwards as indicated in figure 5. Remove the two filter clipsB (fig. 6) and the acrylic or metal panel C. To reassemble the part, simply perform the procedure in reverse.
• FILTER REMOVAL
WARNING - ENSURE THE APPLIANCE IS SWITCHED OFF AT THE MAINS BEFORE REPLACING THE BULBS AND FILTERS.
1.remove the filters by lifting the recessed handle and lift free from the hood frame.
2.To reinstall the filters position in the recess at the rear and press to lock in position.
BULB REPALCEMENT
1.Remove the filters
2.Unscrew the bulb in an anti-clock wise direction.
3.After installing the correct replacement bulb, refit the filter.
Replacement bulbs can be easily obtained from a good electrical or DIY store.
BEFORE CALLING SERVICE/TROUBLE SHOOTING
The hood was switched on but the unit does not operate.
•Have you plugged in/switched on the power supply at the socket?
•Check for a blown fuse/or trip.
Extraction is poor
•Check and clean the filters if required, if required, if active filters are present replacement filters maybe required.
•Check that the exhaust ducting is not obstructed.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS.
