General Guidelines

Before installing and /or using the cooker hood, please read these instructions carefully.

Before installing the cooker hood make sure the volt- age (V), frequency (Hz) indicated on the serial num- ber plate and specifications on the rating plate on the inside of the cooker hood correspond to the voltage and frequency of the mains supply.

INSTALLATION

The cooker hood must not be installed and connect- ed to flues where other appliances are installed and which run off other energy supplies other than elec- tricity (water heaters - boilers - cookers, range/gas etc). The extraction hood requires a 125mm extrac- tion pipe connected directly to the outside with an opening of a minimum cross section of 150cm2.

The hood must be installed with a distance of 650- 750mm between the cooker top/hob and the extrac- tion hood. The cooker hood must not be installed above cookers with eye-level grills.

ELECTRICAL CONNECTION

This cooker hood is designed for permanent fixture. Connect to mains supply. Check voltage and fre- quency given on the rating plate located on the inside of the hood. Connect the mains cable to a power socket or to a double pole switch with a con- tact gap of at least 3mm. The mains cable (type H05VV- F 2x 0.75 mm2) is connected to terminals marked with the letters L (power line) and N (neutral) mounted on the hood and is secured in position by a cable gland. The mains cable must be connected to a suitable and easily accessible fixed power point. As the electrical installation must comply with the laws and regulations in force only a qualified and authorised electrician must install the hood including connecting it to a double pole switch with a contact gap of at least 3mm.

Connect the mains cable if provided with a plug to a power socket. The user must have access to the power socket to be able to connect and disconnect the plug once the hood is mounted and fixed or the mains cable can be plugged into a socket with a dou- ble pole switch with a contact gap of at least 3mm.

The manufacturer will not be responsible if the gov- erning health and safety laws are not observed which permit safe and correct use of the hood and electrical connections.

INSTRUCTIONS FOR ASSEMBLY

The hood is intended for fitting on the wall. Position the hood 70cm above the hob. Remove the metal anti-grease filters. Position the hood against the wall and mark on the wall the position of the support holes. Using a drill bit with a diameter of 6mm., make holes in the wall on the reference marks made previously. Insert the expansion fixings in the holes and then screw the support screws half-way in. Hook the hood onto the screws and fasten it onto the wall, tightening all the screws. Fit the coupling to the top of the hood using self tapping screws provided. Connect the discharge pipe to the coupling. Replace the metal anti-grease filters.

The steel ducting for the hood is to be fixed to the wall using the bracket supplied, the bracket is to be fixed nearest the ceiling and fixed to the end of the duct with slots in it.

CONTROL PANEL

The control panel is situated on the front of the hood and comprises of 5 push button switches with the fol- lowing functions:

Fan ON/OFF switch

Low fan speed

Medium fan speed

High fan speed

Light ON/OFF switch

MAINTENANCE

Before servicing or repairing the hood make sure the appliance is disconnected from the mains supply either by removing the plug or switching the power socket to OFF.

a) Cleaning

“NOTE: the areas behind the filters are not intended to be cleaned”

Clean the external parts with non-corrosive liquid detergents, avoiding the use of abrasive powders or of brushes.

b) Cleaning the metal anti-grease filter

The saturation of greasy residue in the metal filter may cause increased inflammability. In order to pre- vent possible fires, the metal filter must be washed

Chimney Hood specifications

Waterford Precision Cycles has long been synonymous with high-quality, handcrafted bicycles, and their Chimney Hood is no exception. This unique and innovative product stands out in the cycling world, combining advanced technology with exceptional craftsmanship to enhance the cycling experience for enthusiasts of all levels.

The Chimney Hood features a distinctive design that not only emphasizes aesthetics but also functionality. Constructed from high-grade materials, it is lightweight yet exceptionally sturdy, ensuring that it can withstand rigorous use under various weather conditions. One of its main features is the aerodynamic profile, which reduces wind resistance, allowing cyclists to gain speed without expending additional energy.

A key technology integrated into the Chimney Hood is its effective ventilation system. This feature is designed to maximize airflow while minimizing drag. The strategically placed vents ensure that crucial airflow is maintained, allowing cyclists to remain cool during intense rides without sacrificing performance. Additionally, the Chimney Hood is equipped with a unique moisture-wicking lining that helps to manage sweat, keeping the rider dry and comfortable throughout their journey.

Another significant characteristic of the Waterford Chimney Hood is its versatility. It is engineered to fit a wide range of bicycle models, making it an ideal accessory for cyclists who own multiple bikes. The adjustable straps and secure fastening system ensure that it can be mounted easily and confidently, enabling quick transitions from one bike to another.

In terms of aesthetics, the Chimney Hood is available in an array of colors and designs that cater to individual preferences. Waterford's attention to detail is evident in the quality of the finishes, ensuring that each product not only performs exceptionally well but also looks great while doing so.

Moreover, the Chimney Hood embodies Waterford's commitment to sustainability, as it is produced with eco-friendly materials and practices. This commitment not only benefits the environment but also appeals to the growing community of environmentally conscious cyclists.

In conclusion, the Waterford Precision Cycles Chimney Hood is more than just an accessory; it is an essential component that enhances the cycling experience through its innovative features, advanced technologies, and stylish design. Whether for casual rides or competitive racing, this product ensures that cyclists can perform at their best while enjoying the ride.