NON-DUCTED Filters, Cleaning, Operation

ALLURE® WS3 SERIES

RANGE HOOD

Page 6

NON-DUCTED FILTERS

If hood is to be installed Non-Ducted:

Purchase a set of (2) Non-Ducted Filters from your local distributor or retailer and attach them to the aluminum mesh filters.

NOTE: For models that are installed in the non-ducted mode, the most effective operation is achieved at speeds 1 and 2. These speeds provide the most efficient and quiet operation during cooking, while maximizing the benefits of the recirculating filtration system.

3.Remove and inspect fuse. If it is not open (blown), additional diagnostics need to be done.

4.Install new fuse.

5.Re-assemble air chute, light wire harness, bottom panel, and filters.

6.Turn on power and check hood/control operation.

CLEANING

WARNING: To reduce the risk of electric shock, disconnect from power supply before cleaning.

Aluminum mesh filters: Clean frequently using hot water and a mild detergent. Filters are dishwasher safe.

OPERATION

Fan: 4 push button switches. Push any button to select one of the four fan speeds. Press another button to change fan speed. Push the same button to turn fan off. A light above each fan button indicates the fan speed.

Lights: Press “on/off” button and lights will come on at their previ- ous light level. Press button again to turn lights off. To increase light level, press the “+” button. To reduce light level, press the “-” button. There are 3 light levels to select.

Delay Off: While fan is running, press the “delay” button to allow the fan to run for 10 minutes and then turn itself off.

Filter Change Indicator: The light above “filter” will come on when it is time to clean your grease filters or check your non-ducted filters. After replacing the cleaned, or new filters, press the “filter” button to turn off the indicator light.

Heat Sentry System: Your range hood is equipped with an ad- vanced Heat Sentry system.

The advanced Heat Sentry system monitors temperature and au- tomatically adjust the fan to the appropriate setting.

1)If the fan is on, the Heat Sentry system will increase the fan setting when the temperature is elevated. If the temperature continues to rise, the Heat Sentry system will continue to in- crease the fan setting until the temperature is stabilized or re- duced. The flashing light above the fan button shows the Heat Sentry system fan setting. Once the temperature has reduced, the Heat Sentry system will change the fan to the original set- ting.

2)If the fan is on or off, the Heat Sentry system will automatically turn the fan on at its highest speed when the temperature is above normal. When the Heat Sentry system is on, the light above the fan button B (Boost) will flash on and off. After the temperature has lowered to normal, the fan will change to the setting prior to the Heat Sentry turning on.

Fuse: The hood control contains a fuse to protect it from power surges. If the fuse has opened (blown), the green fan-level indica- tors will operate properly when the fan buttons/switches are pressed - but the fan and lights will not turn on.

The fuse is a 5 x 20 mm, 10 Amp, Fast-Acting, 125V (min.). Com- mon manufacturer and part numbers are: Littlefuse, 217010; Bussmann, GMA10A; Wickmann, 1942100. Radio Shack, Digikey (1-800-344-4539), and most electronic supply stores have them in stock.

To replace the fuse:

1.Disconnect power at service entrance.

2.Remove filters, bottom panel, light wire harness, and air chute.

Charcoal filters: Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special “Clean Sense” feature indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The “Clean Sense” feature works best when facing toward the cooking surface.

To clean hood: Remove filters. Use a damp cloth and a mild deter- gent to wipe all grease-laden surfaces. Do not use abrasive cloth, steel wool pads, or scouring powder on the Teflon®-coated bottom cover or on any painted surface. Use care when cleaning blower wheel - it must not become bent or misaligned. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure all surfaces are com- pletely dry before re-installing filters and restoring power.

Motor is permanently lubricated. Do not oil or disassemble motor.

Teflon® is a registered trademark of DuPont.

WS3 specifications

The NuTone WS3 is a state-of-the-art wireless doorbell system that combines sleek design with advanced technology to enhance home connectivity and security. Designed for the modern homeowner, the WS3 offers a range of features that cater to convenience and ease of use.

One of the standout characteristics of the WS3 is its wireless connectivity. This allows for easy installation without the need for complicated wiring or electrical work. Simply mount the doorbell at your desired location, connect it to the wireless network, and you're ready to go. This flexibility makes it an ideal choice for renters or those looking to avoid DIY home improvement projects.

The WS3 comes equipped with a high-definition camera that provides clear visuals of visitors at your door. This feature not only enhances security by allowing homeowners to see who is approaching, but it also provides peace of mind when you’re away from home. The camera includes night vision capabilities, ensuring that you can monitor your entrance around the clock.

Another key feature of the NuTone WS3 is its two-way audio communication. This allows homeowners to interact with visitors in real-time, whether they are at home or away. The built-in microphone and speaker let you speak directly to the person at your door, which is especially beneficial for package deliveries or unexpected visits.

The WS3 also offers customizable chimes and notification settings. Users can select from a variety of sounds for different scenarios, ensuring that you'll never miss a visitor. These customizable options enhance the overall user experience and allow for personalization.

One notable technology incorporated into the WS3 is motion detection. The system can detect when someone approaches the door, sending instant alerts to your smartphone. This added layer of security helps keep homeowners informed about movement around their property, even if they do not frequently check their doorbell camera.

In addition to these features, the NuTone WS3 is backed by a robust mobile app that allows users to access all functionalities from the palm of their hand. The app provides live video feeds, recorded footage, and options for managing alert settings, further enhancing the convenience and control homeowners have over their home security.

With its blend of advanced technology, user-friendly interface, and stylish design, the NuTone WS3 stands out as an exceptional choice for anyone seeking a reliable and efficient wireless doorbell system. Whether you prioritize security, convenience, or aesthetic appeal, the WS3 delivers on all fronts, setting a new standard in home enhancement solutions.