NuTone WS2 Motor Slots, Stop Edge Screw Ties, Metal Strip Plate, TOP Rectangular Duct Knockout

Page 4

ALLURE® WS2 SERIES RANGE HOOD

Page 4

PREPARE THE HOOD

PREPARE THE HOOD

RETAINING BLOWER TAB

RING WHEEL

SECTIONS

MOTOR

SLOTS

SMALL DIAMETER

END

RING

STOP

EDGE

SCREW TIES

10Non-Ducted Installations Only: Require a Performance Ring to be attached to the blower wheel.

To install ring:

1.Remove the Blower Wheel by rocking it side to side and applying a slight force to pull wheel from motor. Remove

Retaining Ring if necessary.

2.Slide the ring onto the Small Diameter End of the wheel and down to the Stop Edge of the wheel.

3.Reassemble wheel to motor. Make sure Tab on wheel fits into one of the Motor Slots.

4.Push wheel down until it is locked in place.

5.Check that wheel is properly positioned as shown. Press Sections into place if necessary. Make sure wheel turns freely.

METAL STRIP

PLATE

12Horizontal Discharge Only: Remove the Plate in front of the horizontal discharge knockout. Cut the Ties, lift plate out, and discard plate. DO NOT REMOVE the Metal Strip held

in place with two Screws.

TOP RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼” x 10” Vertical

REAR

RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼” x 10” Horizontal Discharge)

11Remove appropriate Duct Knockout from top or back of hood.

TAPE

TOP/BACK

UP TO 1”

EDGE

SIDE-TO-SIDE

 

ADJUSTMENT

 

DAMPER/

PIVOTDUCT CONNECTOR

(Vertical

discharge

position shown)

133¼” x 10” Ducted Discharge Only: Remove Tape from damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under “PREPARE THE HOOD”. Make sure damper Pivot is nearest

to Top/Back Edge of hood.

NOTE

Damper/Duct Connector can be installed up to 1-inch on either side of hood center - to accomodate off-center ductwork. In extreme off-center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp.

Image 4
Contents Table of Contents For Domestic Cooking onlyDamper Duct Connector Prepare Hood LocationPrepare the Hood FiltersElectrical Cable Clamp AIR Chute Baffle Slots TabsLight PanelSIDE-TO-SIDE Adjustment Damper Pivotduct Connector Motor SlotsStop Edge Screw Ties Metal Strip PlateConnect Wiring Install Hood NON-DUCTED Filters CleaningOperation Service Parts KEY NO. Part no DescriptionWarranty Nutone ONE Year Limited WarrantyAvertissement Table DES MatièresPréparez L’EMPLACEMENT Préparez LA HottePanneau Inférieur Avec Enduit Raccord DE Conduit Avec RegistreSERRE-FILS DU Câble D’ALIMENTATION Bord Limite Ouverture Préamorcée Supérieure Pour Conduit RectangulaireConduit Avec OuvertureCâble ’ALIMENTATION DU Panneau Principal VIS Verte DE Mise TerreOuverture EN Forme DE VIS D’ASSEMBLAGE 4 Trou DE Serrure Ruban Adhésif Pour Sceller LES ConduitsFonctionnement Filtres Sans ConduitEntretien Pièces DE Remplacement 28 R501034 Autotransformateur avec vis d’assemblageGarantie Garantie Limitée DE UN AN DE Nutone
Related manuals
Manual 16 pages 39.77 Kb

WS2 specifications

NuTone WS2 is a state-of-the-art wireless intercom system designed to enhance communication and convenience within a home. This innovative device seamlessly integrates advanced technologies and user-friendly features, making it a valuable addition to any modern household.

One of the main features of the NuTone WS2 is its wireless connectivity, which eliminates the need for cumbersome wiring. This allows users to place intercom units in various locations throughout the home without the hassle of installation complications typically associated with wired systems. The WS2 operates on a reliable frequency, ensuring clear audio transmission and minimal interference from other electronic devices.

The WS2's crystal-clear sound quality is one of its standout characteristics. Equipped with high-fidelity speakers, it provides crisp and clear audio, which is essential for effective communication. Whether users are talking from one room to another, checking in with family members, or broadcasting messages, the sound remains consistent and is easily understood.

Another significant technology incorporated into the NuTone WS2 is its user-friendly interface. With a simple touch-sensitive keypad, users can navigate through various functions, such as initiating a conversation, adjusting volume levels, and selecting different pre-set channels. This intuitive design ensures that individuals of all ages can operate the system effortlessly.

Additionally, the WS2 is equipped with a dedicated mobile app, which enhances its functionality. This innovative feature allows homeowners to communicate with the intercom system remotely via their smartphones. Users can receive alerts, make announcements, and even engage in conversations from anywhere within their Wi-Fi range, turning their mobile devices into effective communication tools.

The NuTone WS2's sleek, modern design fits seamlessly into contemporary home décor. Its compact form factor and aesthetically pleasing finish ensure that it complements the interior while remaining functional. Furthermore, the flexible mounting options allow users to choose their preferred setup, whether wall-mounted or placed on a countertop.

Security is also a key consideration in the design of the WS2. The system includes features to enhance home safety, such as the option to connect to existing security systems, ensuring that communication is not just limited to intercom tasks but also contributes to overall home monitoring.

In summary, the NuTone WS2 is a versatile and modern intercom system that combines wireless technology, exceptional sound quality, and user-friendly features. Its innovative design and capabilities make it an excellent choice for enhancing communication within any household.