Napoleon Fireplaces SAVOY OS11 manual Mobile Home Installation, Chimney installation

Page 7

Document n° 1043-1 ~ 15/01/2002

 

7

There are two types of chimney connectors :

 

 

A single wall chimney connector may be used for top

 

 

connection :

 

 

This connector must be 316 grade 26 gauge stainless steel or 1 mm

 

 

vitreous enamelled steel and with a 5" (127 mm) diameter. Secure

 

 

the connector joints with 3 sheet metal screws. The joints are to be

 

 

airtight. All connector sections must be attached to the unit and to

 

 

each other with the crimped or male end pointing down towards the

 

 

oil stove.

 

 

Use a double wall chimney connector for rear connec-

 

 

tion :

 

 

The connector should be of the same make (manufacturer) as the

Figure 5

Figure 6

chimney components.

 

 

Chimney installation

Connection to a A-VENT chimney :

An A-Vent chimney, either 4" (101,6 mm.) or 5" (127 mm.) in diameter may be used. The minimum chimney height is to be 15 feet or 4.6 metres measured from the appliance flue collar to the top of the chimney but not including any chimney caps. Installation of all chimney systems is to be in accordance with the chimney manufacturers installation instructions. If the stove is to be connected to a masonry chimney, a stainless steel liner is required. DO NOT USE ANY MAKESHIFT

MATERIALS DURING INSTALLATION.

2 FT.

 

min 10 FT.

3 FT.

 

min

Figure 7

1.Move the stove into position with the flue centred, mid point between two joists to prevent having to cut them. Use a plumb bob to line up the centre.

2.Cut and frame an opening in the roof to provide a 2" (50 mm) clearance between the outside of the chimney and any combustible material. DO NOT FILL THIS SPACE WITH ANY TYPE OF MATERIAL.

Nail headers between the joists for extra support. Firestop spacers must be placed on the bottom of each framed opening in any floor or ceiling that the chimney passes through (figure 5).

3.Hold a plumb bob from the underside of the roof to determine where the opening in the roof should be. Cut and frame the roof opening to maintain proper 2" (50 mm) clearances (figure 6).

Example : A = Chimney diameter + 2 times the required clearance from chimney to combustible framing materials.

Connection to a L-VENT chimney :

This appliance is certified to be connected to a L-VENT chimney, 5" (127 mm). Use NAPOLEON ADAPTOR, W 175-0198. This adaptor is specifically designed for Energy Vent Chimney.

Adding chimney sections

Add chimney sections, twist locking (clockwise) securely, to the required height. Safety requirements dictate that the chimney must be at least 3 feet (915 mm) higher than the highest point where it passes through the roof and at least 2 feet (610 mm) higher than the highest part of the roof or structure that is within 10 feet (3.05 m) of the chimney, measured horizontally (figure 7). Obstacles close to the chimney may cause down drafts which may be prevented by the installation of a chimney cap fitted with a wind deflector. If your chimney system is enclosed within the attic area, a rafter radiation shield is required.

MOBILE HOME INSTALLATION

In mobile home installation, the oil stove must be installed with an oil drip tray. Order this part, 72636, from your Napoleon dealer

When installing the OS11 into a mobile Home, a carburetor support (supplied) must be installed for extra support of the carburetor (fig. 4). Ensure the support is adjusted to make contact with the floor. Outside air intake is mandatory in mobile homes only.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Savoy OS11 Introduction ContentsNapoleon OIL Stove PRESIDENT’S Lifetime Limited Warranty Care of enamelled parts InstallationUnit and specifications General informationDraft air Safety precautionsCombustion air for NON mobile home installation Location and clearancesChimney connector Chimney specificationsChimney installation Mobile Home InstallationAdding chimney sections Fuel Supply FinishingTop flue outlet Understanding your oil stove Operating InstructionsLighting instructions Overheating AdjustmentsOil flow adjustments Shut downSeasonal maintenance MaintenanceRemoving the flue baffle Replacement parts Ordering replacement partsDocument n 1043-1 ~ 15/01/2002 Document n 1043-1 ~ 15/01/2002 Trouble Shooting

SAVOY OS11 specifications

The Napoleon Fireplaces SAVOY OS11 is a remarkable addition to the lineup of premium fireplace solutions, known for its elegant design and superior heating capabilities. This stylish gas fireplace not only enhances the aesthetic of any living space but also offers innovative technologies that ensure efficient and effective heating for your home.

One of the standout features of the SAVOY OS11 is its large viewing area. The expansive glass front allows for an unobstructed view of the mesmerizing flames, creating a stunning focal point in any room. The frameless design provides a sleek, modern appearance that complements a variety of interior styles, from contemporary to traditional.

The SAVOY OS11 is equipped with Napoleon’s patented PHAZER® log set, which perfectly mimics the look of real wood burning. The high-definition, handcrafted logs enhance the realistic appearance of the fire, while the advanced technology behind the flame produces a vibrant and lifelike flame pattern that adds warmth and ambiance to your home.

In terms of heating performance, the SAVOY OS11 boasts impressive efficiency ratings. With an input of up to 30,000 BTUs, this fireplace can effectively heat large areas, ensuring comfort on even the coldest of nights. Its dual burner system provides the option to adjust the flame height and heat output, allowing users to customize their experience based on their specific needs.

Moreover, the latest in safety features ensures peace of mind when using the SAVOY OS11. The fireplace is designed with a safety shut-off valve that automatically turns off the gas supply in the event of a malfunction. Additionally, the unit is equipped with a child safety barrier and a tempered glass front to prevent accidental burns.

Installation and maintenance are made convenient with the SAVOY OS11, as it can be easily integrated into both new and existing homes. The fireplace is compatible with a variety of venting options, giving homeowners flexibility in how they choose to incorporate it into their living space.

Overall, the Napoleon Fireplaces SAVOY OS11 is a perfect blend of sophisticated design and cutting-edge technology. With its impressive heating efficiency, realistic flame presentation, and safety features, it stands out as a leading choice for those looking to elevate their home heating experience.
Top Page Image Contents