General Instructions

THIS GAS FIREPLACE INSERT SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁcs that apply to your area,

for example: in Massachusetts State:

•The ﬁreplace damper must be removed or welded in the open position prior to installation of a ﬁreplace insert or gas log.

•The appliance off valve must be a “T” handle gas cock.

•The ﬂexible connector must not be longer than 36 inches.

•The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

•WARNING: This product must be installed by a licensed plumber or gas ﬁtter when installed within the commonwealth of

Massachusetts.

In absence of local codes, install to the current CAN1-

B149 Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1, and NFPA 54 in the United States. Mobile home installation must conform with local codes. In the absence of local codes, install to the current standard for gas equipped mobile housing CAN/CSA Z240 MH Series in Canada or the manufactured home construc- tion and safety standard, Title 24 CFR, part 3280, or the Fire Safety Criteria for manufactured home installations, Sites and Community Standard ANSI/NFPA 501A in the United States.

Purge all gas lines with the glass door of the ﬁreplace insert opened. Assure that a continuous gas ﬂow is at the burner before closing the door.

Under extreme vent conﬁgurations, allow several minutes (5-15) for the ﬂame to stabilize after ignition.

The ﬁreplace insert and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The ﬁreplace insert must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

A 1/8 inch NPT plug, accessible for test gauge connection, must be installed immediately upstream of the gas supply connection to the ﬁreplace insert.

The fireplace insert must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELEC- TRICAL CODE in Canada or the ANSI/NFPA 70-1990 NA- TIONAL ELECTRICAL CODE in the United States. The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

GENERAL INFORMATION

FOR YOUR SATISFACTION, THIS FIREPLACE INSERT HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!

Minimum inlet gas supply pressure is 4.5 inches water col- umn for natural gas and 11 inches water column for propane. Maximum inlet gas pressure is 7 inches water column for natural gas and 13 inches water column for propane. Manifold pressure under ﬂow conditions is 3.5 inches water column for natural gas and 10 inches water column for propane. When the ﬁreplace is installed at elevations above 4,500ft, and in the absence of speciﬁc recommendations from the local authority having jurisdiction, the certiﬁed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft.

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

Maximum input is 24,000 BTU/hr for natural gas and propane. Maximum output for natural gas and propane is 20,400 BTU/ hr at an efﬁciency of 85% with the fan on. Maximum A.F.U.E. (annual fuel utilization efﬁciency) rating is 79 % for natural gas and propane. This ﬁreplace insert is not approved for closet or recessed installations. It is approved for bathroom, bedroom and bed-sitting room installations and is suitable for mobile homes. The natural gas model is suitable for installation in a mobile home that is permanently positioned on its site and fuelled with natural gas.

This insert must be recessed into a vented noncombustible wood-burning ﬁreplace (prefabricated or masonry) only. The minimum ﬁreplace opening size in which the heater is to be installed is:

HEIGHT	14½	inches
WIDTH	25	inches
DEPTH	11	inches

The minimum allowable chimney ﬂue size is 6" round. The minimum distance, from the bottom of a combustible mantle projecting 3" maximum from the wall to the top of the aluminium trim, is 3".

65.5%

GDIZC

CARE OF GLASS, AND PLATED PARTS

Do not use abrasive cleaners to clean these parts. Buff lightly with a clean dry cloth.

The glass is 3/16" ceramic glass available from your Napoleon

/Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the ﬁrst 10 hours of operation with a recommended gas ﬁreplace glass cleaner. Thereafter clean as required. DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or blemishes may result.

W415-0223 / E / 03.05.09

GDIZC-N specifications

Napoleon Fireplaces has long been recognized as a leader in the fireplace industry, and the GDIZC-N and GDIZC-P models are prime examples of their commitment to innovation and quality. These modern, two-sided gas fireplaces are designed to offer both aesthetic appeal and functional efficiency, making them ideal for a wide range of residential settings.

The GDIZC-N (natural gas) and GDIZC-P (propane) are contemporary gas fireplaces that can be installed in a variety of configurations, including as a room divider or as a standalone feature in a living room or dining area. Their unique design allows for maximum viewing from two sides, creating a stunning focal point that enhances the ambiance of any space. The clean lines and sleek design fit seamlessly into modern architecture while providing warmth and comfort.

One of the standout features of the GDIZC models is their superior heating capabilities. With an impressive heat output of up to 30,000 BTUs, these fireplaces ensure that your home remains cozy during the coldest months. They are equipped with high-efficiency heat exchangers that maximize warmth while minimizing heat loss. This efficiency not only contributes to comfort but also helps in reducing energy costs, making them an economically sound choice for homeowners.

Another notable characteristic of the GDIZC-N and GDIZC-P is the radiant heat technology. This system uses direct heat to warm objects and people in the room, creating an inviting atmosphere. Additionally, the fireplaces are designed with an electronic ignition system, allowing for easy start-up and consistent operation. The inclusion of a built-in safety shut-off feature ensures peace of mind when using these efficient heating units.

Moreover, Napoleon has incorporated contemporary styling options, including customizable media trays and a range of decorative media choices like glass beads and driftwood logs. The advanced LED lighting enhances the realistic flame effect and allows for customizable ambiance, giving users the ability to set the perfect mood for any occasion.

The GDIZC-N and GDIZC-P models are also designed with ease of installation in mind. They come with a versatile venting system, allowing for various venting options to accommodate different home layouts. This flexibility makes it easier for homeowners to integrate these stunning fireplaces into their existing spaces without significant renovations.

In summary, the Napoleon Fireplaces GDIZC-N and GDIZC-P models stand out for their impressive heating capabilities, elegant design, and technological features. With their two-sided viewing, advanced efficiency, and extensive customization options, these fireplaces are a perfect combination of functionality and style for modern living environments. Whether enhancing a cozy living space or serving as a striking room divider, these fireplaces deliver warmth and beauty that any home can benefit from.