Hunter Fan 90066, 90067 warranty R N I N G, Before Installation

W A R N I N G

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

Check all the parts. If damaged, call 1-888-830-1326 for replacements.

D95044-01-000

E95022-01-000

1.	Use this unit only in a manner intended by the manufacturer.
	If you have questions, contact the manufacturer at the phone
	number or address listed in the warranty.
2.	Before installing, servicing, or cleaning the unit,
	disconnect the power by turning off the circuit breakers to
	the outlet box and associated wall switch location. If you
	cannot lock the circuit breakers in the off position, securely
	attach a prominent warning device, such as a tag, to the
	service panel.
3.	Installation work and electrical wiring must be done by
	qualified person(s) in accordance with all applicable codes
	and standards, including fire-rated construction codes and
	standards.
4.	Sufficient air is needed for proper combustion and exhaust-
	ing of gasses through the flue (chimney) of fuel burning
	equipment to prevent backdrafting. Follow the heating

such as those published by the National Fire Prevention Association (NFPA), and the American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities.

6.Ducted fans must always be vented to the outdoors. Keep ducting as short and as straight as possible.

7.Acceptable for use over a bathtub or shower when connected to a GFCI protected branch circuit.

8.Install fan at least 5 feet (1.52 m) above the floor.

9.Never place a switch where it can be reached from a tub or shower.

10.This unit must be grounded.

x5 A

*B

3/8" Cable Connector

*C

x2 I Extra Screws

*NOTE: Strain relief cable connector must be installed. Not Included.

F75190-01-000

G03242-07-133

H95492-02-000

x2	I	74508-03-133
x4	J	75184-01-133

K84724-01-000

L95512-01/02/-000

M75016-01-000

N95011-01/02/-000

Pre-assembled

95013-01/02-000 0

equipment manufacturer’s guideline and safety standards,

Included.

C A U T I O N

1.For general ventilating use only. Do not use for ventilat- ing hazardous or explosive materials.

2.To avoid motor bearing damage and noisy/unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3.DO NOT install this product in a wall. This product is designed for installation in ceilings up to a 12/12 pitch (45 degrees). Ductwork must point upward.

4.Please read specification label on product for further information and requirements.

W A R N I N G

DISCONNECT

ELECTRIC

POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE SERVICING UNIT

Tools Needed.

Estimated assembly time: 30 to 60 minutes.

Before Installation

PREVENTATIVE MAINTENANCE

NOTE: Remove all packing materials before installation.

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same time.

1	2	OFF
	30	OFF
	30
		OFF
		30
		OFF
	30	OFF
	30

Turn off the power source.

2

I

E

Loosen screws.

2 41723-01 12/25/2004 41723-01 12/25/2004 3