Venting Requirements, Electrical Requirements

VENTING REQUIREMENTS

Determine which venting method is best for your applica- tion. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient perfor- mance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or floor opening around the cap.

Flexible ductwork is not recommended. If it is used, each foot of flexible ductwork used is equivalent to two feet of straight metal ductwork when calculating the ductrun length. Thus, a flexible elbow equals two standard elbows.

Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

FOR MORE SPECIFIC DUCTWORK INFORMATION,

GO TO PAGE 5.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

!WARNING

•Venting system MUST terminate outside the home.

•DO NOT terminate the ductwork in an attic or other enclosed space.

•DO NOT use 4" laundry-type wall caps.

•Flexible-type ductwork is not recommended.

•DO NOT obstruct the flow of combustion and ventilation air.

•Failure to follow venting requirements may result in a fire.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as specified on the serial/rating plate located inside the unit near the field wiring compartment. THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size and connec- tions must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

For residential use only.

This appliance should be connected directly to the fused disconnect (or circuit breaker) through flexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever necessary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet.

WARNING - TO REDUCE THE RISK OF FIRE OR ELEC- TRIC SHOCK, do not use this fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have any ques- tions, contact the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accor- dance With All Applicable Codes And Standards, In- cluding Fire-Rated Construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Soci- ety for Heating, Refrigeration and Air Conditioning Engi- neers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

!WARNING

•Electrical ground is required on this rangehood.

•If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding.

•DO NOT ground to a gas pipe.

•DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.

•Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded.

•DO NOT use this appliance with any solid state fan speed control device.

•Failure to follow electrical requirements may result in a fire.

Version Hi-Lo 02/04 - Page 2

6048624 specifications

The Faber 6048624 is a highly acclaimed range hood designed to enhance kitchen functionality while complementing modern décor. Known for its efficiency and cutting-edge features, the Faber 6048624 exemplifies the perfect blend of style and performance, making it a preferred choice for homeowners and professional chefs alike.

One of the standout features of the Faber 6048624 is its powerful extraction capacity. It utilizes a robust motor to efficiently remove smoke, grease, and odors from the kitchen, ensuring clean air circulation. With adjustable air flow settings, users can tailor ventilation according to their cooking needs, providing versatility for everything from simmering sauces to frying meats.

The design of the Faber 6048624 is both sleek and functional, available in various finishes to suit different kitchen styles. Its minimalist aesthetic allows it to seamlessly integrate into any kitchen environment, whether it be contemporary or transitional. Furthermore, its space-saving design can be mounted under cabinets or as a standalone unit, maximizing kitchen space.

In considerations of technology, this range hood boasts advanced noise reduction features. Many users appreciate the quiet operation of the Faber 6048624, which allows kitchen conversations to flow uninterrupted while maintaining efficient ventilation. This low-noise technology is a significant benefit for open-concept living spaces.

Additionally, the Faber 6048624 includes innovative LED lighting that illuminates the cooking surface, enhancing visibility and safety while preparing meals. This feature not only improves the cooking experience but also adds an aesthetic touch to the kitchen.

Maintenance is also a crucial aspect of the Faber 6048624. It is equipped with easy-to-clean filters that can be removed and washed, promoting hygiene and ensuring optimal performance over time. The filter indicators provide reminders for when the filters need to be cleaned or replaced, taking the guesswork out of maintenance.

Overall, the Faber 6048624 stands out due to its effective design, impressive extraction capabilities, modern aesthetics, and user-friendly features. It is perfect for those looking to invest in a quality range hood that combines style with functionality, making kitchen chores easier and more efficient. Whether you are an amateur cook or a culinary expert, the Faber 6048624 is sure to enhance your cooking experience.