Zanussi ZDT 6253 manual Something not working, Symptom, Code, Solution

Page 14

Something not working

Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an enginee

r.

The dishwasher is fitted with a number of alarm systems which can help you to quickly determine the cause of any problems.

In the case

of alarm intervention the dishwasher will not start or stops during operation, all push buttons are inoperative exc

ept for

the ON/OFF push button. All indicator lights are off except for the ON/OFF indicator light.

 

One of the

programme indicator lights starts flashing to indicate which kind of fault has occurred.

 

Press the ON/OFF push button to switch the dishwasher off and open the door, carry out the following suggested corrective actions listed below.

Once the checks have been carried out switch on the dishwasher and start a washing programme, if the fault code reappears, contact your local Service Force Centre.

Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is in guarantee.

Symptom

Fault

code

Solution

 

 

 

 

 

 

The machine will not start

 

 

 

The door has not been properly closed.

 

 

 

 

The plug is not properly inserted in the power socket.

 

 

 

 

There is a power failure.

 

 

 

 

 

The machine does not fill

number 1 programme push

 

Ensure the water tap is open.

with water

button indicator light

 

Ensure the mains water supply has not been cut off.

 

 

flashing

 

The inlet hose may be squashed or bent. Reposition the hose.

 

 

 

 

The inlet hose may be blocked. Switch off the water supply and

 

 

 

 

clean the filter.

 

 

 

 

Protection against flooding is active. Close the water tap and contact

 

 

 

 

the Service Force Centre.

The filters are blocked

number 2 programme push

 

Clean the filters (refer to "Maintenance and cleaning").

 

 

button indicator light

 

 

 

 

flashing

 

 

 

 

 

 

 

The dishwasher will not drain

number 5 programme push

 

The drain hose may be squashed or bent.

 

 

button indicator light

 

Reposition the hose.

 

 

flashing

 

The sink may be blocked. Clear any blockages.

 

 

 

 

The drain hose extension is not correct. Follow the instructions for

 

 

 

 

connecting to the waste.

 

 

 

 

There is no vent in the end of the drain hose.

 

 

 

 

 

General

number 3 or 4 programme

 

Switch off the dishwasher, switch it back on and start the

 

 

push button indicator

 

programme. if the alarm reappears, call the local Service

 

 

light flashing

 

Force Centre.

 

 

 

 

 

The machine is noisy

 

 

 

Dishes are rattling against each other, refer to “Loading

 

 

 

 

your machine” (Instruction book - part 2).

 

 

 

 

The spray arms are knocking against the dishes. Refer to

 

 

 

 

"Loading your machine" (Instruction book - part 2).

 

 

 

 

 

The door is difficult to close

 

 

 

The dishwasher is not level, or not properly built-in.

 

 

 

 

 

Visible lime deposits or white film

 

 

 

Check that there is salt and that the salt cap is tight.

on the dishes

 

 

 

Check that the right level of the water softener is set.

 

 

 

 

 

The dishes are not quite dry

 

 

 

The rinse aid has run out or too little is being used.

 

 

 

 

 

The dishes are not clean

 

 

 

The baskets are too full.

(poor wash)

 

 

 

The dishes have not been arranged properly.

 

 

 

 

The spray arms do not rotate

 

 

 

 

The spray arms are clogged.

 

 

 

 

The filters are clogged.

 

 

 

 

The filters are not in the correct position.

 

 

 

 

Not enough detergent has been used or it is unsuitable.

 

 

 

 

The detergent is old or has gone hard.

 

 

 

 

The salt container cap is not properly closed.

 

 

 

 

The washing programme selected is too gentle.

 

 

 

 

 

If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. This information can be found

on the rating plate located on the right hand side of the dishwasher door.

Prod.No.

......Ser..No

Mod

 

RA01

 

This product should be serviced by an authorised Service engineer, and only genuine spare parts should be used. Under no circumstances should you attempt to repair the machine yourself.

Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Force Centre.

Always insist on genuine spare parts.

6

Image 14
Contents Dishwasher Control panel Salt indicator lightDescription of the appliance On/Off push button Half load push buttonWashing programmes Operating sequence Using your appliance Protection against flooding Technical specificationsHints for test centres Customer Care Department Service and Spare PartsGuarantee Conditions From the Electrolux Group. The world’s No.1 choice 01/02Contents Important safety informationFilling with salt Setting the water softenerBefore use To fillFilling with rinse aid Adjusting the doseRinse aid Use of detergentFor best washing and drying results Hints and tipsTo save energy Items not suitable for dishwashersMaintenance and cleaning Something not working SymptomSolution CodeWater supply connections InstallationLevelling Water outlet hose connection01/02