AX5103(G)2007.8.174:43PM페이지 9
Operations
LISTENING TO A PROGRAM SOURCE
Before operation | 2 | Switch the desired speakers on. | ||||||
• Enter the standby mode. |
|
|
|
|
| |||
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
or
• The STANDBY indicator lights up. | • Then the corresponding SPEAKER indicator lights up | |||||||||||||||
This means that the amplifier is not disconnected from | and the sound can be heard the speakers connected | |||||||||||||||
the AC mains and a small amount of current is | to "SPEAKER A" or (and) "SPEAKER B" terminals. | |||||||||||||||
retained to support the memorized contents and | • When using headphones for private listening, press | |||||||||||||||
operation readiness. | both SPEAKER SELECTOR A and B buttons to switch | |||||||||||||||
• To switch the power off, push the POWER switch | the speakers off. | |||||||||||||||
again, then the power is cut off and the STANDBY | Note : For safe amplifier operation, be sure to check | |||||||||||||||
indicator goes off. |
| impedance of the speakers connected. (Refer to | ||||||||||||||
|
|
|
|
|
|
|
| “CONNECTING SPEAKERS” on page 6) | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| In the standby mode, turn the power on. |
| ||||||||||||||
1 |
| 3 |
|
| Select the desired input source. | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| or | ||||
• Each time the POWER button on the remote control |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| |
is pressed, the amplifier is turned on to enter the |
|
|
|
|
|
operating mode or off to enter the standby mode. |
|
|
|
|
|
• In the standby mode, if the INPUT SELECTOR | • Then the corresponding indicator lights up. | ||||
button is pressed, the amplifier is turned on | • When the TAPE 2 MONITOR button is set to on so that | ||||
automatically and the desired input is selected. | the TAPE 2 MONITOR indicator lights up, other inputs | ||||
| can not be heard from the speakers. | ||||
�SYSTEM POWER ON/OFF | To listen to a input source other than TAPE 2 | ||||
• If the POWER switch of Sherwood component | MONITOR, be sure to set the TAPE 2 MONITOR | ||||
connected by the DIGI LINK II or III is kept pushed | button to off. | ||||
and its AC input cord is plugged in the switched AC | TAPE MONITOR function | ||||
outlet, each time the amplifier becomes the standby | |||||
or the operating mode, its power is turned off or on. | You can connect either a tape deck or a graphic | ||||
• Under the same conditions, if its AC input cord is not | equalizer to the amplifier’s TAPE 2 MONITOR jacks. | ||||
plugged only in the switched AC outlet, when the | Only when you listen to the component connected to | ||||
amplifier becomes the standby mode, only its display | these jacks, set the TAPE 2 MONITOR button to on. | ||||
is off (meaning that a small amount of current is | If you connect a | ||||
retained for operation readiness, etc.) | sound being recorded during recording, not the source | ||||
| sound. | ||||
| For further details, refer to the operating instructions of | ||||
| the component connected. | ||||
ENGLISH
10