Tricity Bendix BD 912 Make the Electrical Connections, HOW to Finish Unpacking, Tools Required

Page 11

HOW TO FINISH UNPACKING

Place packed cooker next to the cabinet in which it will be installed.

Remove the cooker packing except for bottom tray which should be left in position until the

lcooker is ready to be fitted into its cabinet.

Ensure the owner is given these operating instructions.

TOOLS REQUIRED

The following tools will be needed and it helps to assemble them before starting to install your oven:

A terminal screwdriver (3mm wide blade) A pozidrive screwdriver

Pliers Wirestrippers Knife Sidecutters Adhesive Tape Tape Measure

MAKE THE ELECTRICAL CONNECTIONS

Important: Switch off at mains, miniature circuit breaker and, if appropriate, remove fuse before commencing any electrical work.

PREPARING CABLE

We recommend you use a new length of cable to ensure your safety.

Ensure you have the correct length of cable appropriate to the wiring method you are using. When fitting new cable allow sufficient cable for removal of the unit at a later date, should it be

lnecessary.

Score, but do not cut through, around the sheathing with a knife 100mm (4in) from each end of the cable and break through to the encased wires by bending the cable backwards and forwards to fatigue the sheathing.

Carefully score down from each end of the cable sheathing along the length of the bare earth wire (if a cut was made along the length of the live or neutral wires, it might cut into their sheathing) to

lthe cuts already made.

Carefully prise open the sheathing at each end of the cable to expose the encased wiring.

TO REMOVE COVER OF MAINS TERMINAL

From the rear of the cooker, remove mains input terminal cover to gain access to terminal block.

First remove retaining screw with pozidrive

lscrewdriver. See Fig. 3.

Fig.3

Prise cover loose using screwdriver in position

(1)then lever off with screwdriver in position (2) at either side. See Fig. 4.

Fig.4

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Better Products. Better Value Model NO. BD Technical DetailsContents Contents Preface During Operation SafetyGeneral After USEThings to Note Installation InstructionsThings YOU Need to Know Getting Things ReadyPreparing Cabinet for Fitting of Oven Millimetres 550mPreparing Cable HOW to Finish UnpackingMake the Electrical Connections Tools RequiredConnecting to a HOB or Cooker Point Connecting to Mains TerminalFitting Into the Cabinet Getting to Know Your Oven IntroductionRating Plate General Notes on Using the OvensWhen First Switching on Control Panel Indicator NeonsGrill and Oven Furniture Minute Minder Electronic Minute MinderTo SET the Time of DAY To Cancel the Minute Minder Things to Note Grill PAN and Handle GrillUses of the Dual Grill Selecting the Dual GrillLHINTS and Tips Food Shelf Grill Time Grilling ChartTo FIT the TOP Oven Shelf Second OvenUses of the Second Oven Selecting the Second OvenPage Selecting the FAN Oven Main FAN OvenUses of the FAN Oven To FIT the Main Oven Shelves FAN Oven TOP Oven Food Shelf Cooking Approx Position Temp C Oven Cooking ChartRoasting Chart Roasting ChartSelecting Defrost Uses of Defrost FeatureDefrosting Meat Temperatures Helpful Hints When Buying and Preparing FoodCleaning Between the Outer and Inner Door Glass Care and CleaningCleaning the Outside Cooker Cleaning Inside the OvensTo Replace the Outer Glass Cleaning Inside the Oven and Grill CompartmentsCare of Stayclean Surfaces Replacing the Oven Light Bulb Something not WORKING? Grill, oven and timer do not workConsumer Care Department Service and Spare PartsService Help US to Help YOUScotland North AST Northern Ireland Wales North West Tricity Bendix Service CentresMidla DS LO on & East Anglia South West South East Exclusions Guarantee ConditionsPage Rating Plate Reference
Top Page Image Contents