Frigidaire 241567600 warranty Before Installing The Water Supply Line, You Will Need

Page 5

Installation - Connecting Optional Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

•Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any damage if plastic tubing is used for supply line.

•DO NOT install water supply tubing in areas where temperatures fall below freezing.

•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

•Access to a household cold water line with water pressure between 20 and 120 psi.

•A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

•A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

•A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule(sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7.Coil excess water supply line (about 2½ turns) behind refrigerator as shown andarrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10.To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/ OFF position of arm).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Use & Care Manual Please Read and Save These Instructions Welcome & CongratulationsFor Your Safety Important Safety InstructionsChild Safety Proper Disposal Ofyour Refrigerator or FreezerInstallation To Connect Water Supply Line To Ice Maker Inlet Valve Before Installing The Water Supply Line, You Will NeedDoor Removal Instructions Door Removal and Reversal InstructionsTo remove freezer door To remove refrigerator doorFeatures At a Glance Cool Down Period Temperature ControlsRefrigerator & Freezer Controls Temperature Adjustment Looking Inside Shelf AdjustmentDoor Storage Adjustable Door BinsTall Bottle Retainer Some Models Special Item Rack Some ModelsWine Rack Some Models Humidity Control Some ModelsWater Dispenser Water Dispenser & Ice ServiceWater pressure must not exceed 100 lbs. Excessive pressure mayDo Not place the ice container in your dishwasher ICE MakerSystem Startup PureSource TM * ICE and Water Filter some modelsChanging the Filter To change filterEnergy Saving Ideas Food Storage & Energy Saving IdeasFood Storage Ideas Drain Pan Nonremovable Normal Operating Sounds & SightsUnderstanding the Sounds YOU MAY Hear Outlet Before Cleaning Care & CleaningReplacing Light Bulbs Wear gloves when replacing light bulbs to avoid cutsCondenser Short Vacations Long Vacations MovingRefrigerator Warranty Warranty InformationRefrigerator temperature is Freezer temperature too coldSatisfactory Refrigerator temperature too cold Freezer temperature is

241567600 specifications

The Frigidaire 241567600 is a highly regarded appliance component, specifically designed as a refrigerator ice maker assembly. This part is essential for those who want to enjoy the convenience of automatic ice production right from their refrigerators, enhancing the overall functionality of the appliance.

One of the main features of the Frigidaire 241567600 is its compatibility with a variety of refrigerator models. This versatility allows it to be a reliable replacement part for numerous Frigidaire models, making it an ideal choice for homeowners looking to restore their refrigerator's ice-making capabilities. The assembly is constructed with durable materials, ensuring long-lasting performance and resistance to wear over time.

The technology incorporated in the Frigidaire 241567600 focuses on efficiency and optimal ice production. The ice maker operates smoothly and quietly, producing clear, well-formed ice cubes that are perfect for beverages and entertaining. With a user-friendly design, the ice maker is easy to operate and maintain, requiring minimal effort to keep it in good working condition.

Another noteworthy characteristic of this ice maker assembly is its energy-efficient performance. Designed to minimize energy consumption, it not only helps in reducing utility bills but also aligns with eco-friendly practices by lowering the overall carbon footprint of your household.

The ice maker comes with a straightforward installation process, making it accessible for those who prefer to tackle home repairs themselves. Clear instructions often accompany the product, allowing for a quick setup that can be carried out with minimal tools.

Overall, the Frigidaire 241567600 stands out in the realm of refrigerator accessories due to its reliability, ease of use, and efficient performance. For homeowners invested in maintaining their refrigerator and enhancing its features, this ice maker assembly is an excellent choice. Whether for daily use or entertaining guests, having an efficient ice maker readily available is indeed a valuable asset in any modern kitchen.
Top Page Image Contents