AUTOMATIC ICE AND WATER DISPENSER
HOWTHE WATER DISPENSER WORKS
The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water is dispensed. For proper dispenser operation, the recommended supply water pressure should fall between 30 psi and 100 psi.
After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about 1½ minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff mechanism.
CAUTION
Water pressure must not exceed 100 lbs. Excessive pressure may cause water filter to malfunction.
Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
to the ice maker, pull the ice cream tray out. Press the switch to the “O” position to turn it Off and press it to the “I” position to turn it On. With no usage it will take approximately 2 days to fill the ice container. The ice maker also has a
The ice maker produces 4 to 6 pounds of ice every 24 hours depending on usage conditions. Ice is produced at a rate of 8 cubes every 75 to 90 minutes.
Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These should be discarded until the cubes made are free of discoloration and taste.
ICE AND WATER DISPENSER FEATURES
The ice and water dispenser conveniently dispenses chilled water, and ice cubes or crushed ice, depending on the model.
To operate the ice dispenser, select the ice option desired using the touchpad. Press a glass against the dispensing paddle as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside of the freezer door.)
HOWTHE ICE DISPENSER WORKS | ICE DISPENSER TIPS |
|
The ice maker and container are located in the top of the freezer compartment. After the refrigerator is installed properly and has cooled for several
hours, the ice maker can
begin making ice within 24 | ON | |
| ||
hours. Air in new plumbing |
| |
lines may cause the ice | OFF | |
maker to cycle two or three |
| |
times before making a full | Wire | |
tray of ice. To begin ice | ||
Signal Arm | ||
| ||
production, lower the wire |
| |
signal arm to the "down" or |
| |
ON position. With no usage it |
|
will take approximately 2 days to fill the ice container.
The ice maker turns off automatically when the ice container becomes full. To stop the ice maker, lift the wire signal arm until it clicks, and locks in the "up" or OFF position.
HOWTHE ICE DISPENSER WORKS -REAR MOUNTED
The ice maker and container are
located in the top of the freezer compartment. After the refrigerator is installed properly
and has cooled for several hours, the ice maker can begin
making ice within 24 hours. Air in new plumbing lines may cause 
the ice maker to cycle two or three times before making a full tray of ice. Ice production is controlled by the ice maker’s On/ Off power switch. To gain access
13
•Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the wire signal arm is in its “down” or ON position (side mounted) or the ice maker’s On/Off power switch is turned
•Occasionally shake the ice container to keep ice separated.
•Keep the wire signal arm in its “up” or OFF position (side mounted) or the ice maker’s On/Off power switch turned
IMPORTANT
Your ice maker is shipped with the wire signal arm in the ON position (side mounted) or turned ON (rear mounted) at the factory. To ensure proper function of your ice maker, hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position (side mounted) or turn the On/Off switch to the Off (“O”) position. If the icemaker is not turned off and the water supply is not connected, the water valve will make a loud chattering noise.