4c & 4-WIRE Permanent Wire Connections

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

(For 3 or 4 Wire, 60 Hz. Systems)

or 4B. POWER CORD CONNECTIONS

(3-Wire Connection Instructions . For existing installations ONLY - Refer to Fig. 13).

1. Follow the manufacturer’s installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11).

2. Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block (See Fig. 13).

IMPORTANT NOTE: DO NOT LOOSEN the factory installed nut connections which secure the range wiring to the terminal block. Electrical failure or loss of electrical connection may occur if these 3 nuts are loosened or removed.

3. Make sure all connections are tightened securely and replace the rear access cover (See Fig. 9).

Grounding Instructions (3-Wire Connections only): A ground strap is installed on this range which connects the center terminal of the terminal block (Neutral) to the range chassis. The ground strap is connected to the range by the center, lowest screw (See Fig. 13). The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap.

NOTE: If the ground strap is removed for any reason, a separate ground wire must be connected to the separate ground screw attached to the range chassis and to an adequate ground source.

4c. 3 & 4-WIRE PERMANENT WIRE CONNECTIONS.

3 - Wire Permanent Connection - follow Steps 1,2 & 5 below.

4 - Wire Permanent Connection - follow Steps 1 thru 5 below. Before wiring the range, review the suggested power source location drawings in Fig. 3. If connecting to a 4-Wire electrical system (new branch- circuit or mobile home requires 4-Wire connection):

1. (3 & 4 - Wire Permanent Connections) Follow the manufacturer’s

installation instructions supplied with the strain relief and install.

2. (3 & 4 - Wire Permanent Connections) Strip insulation away from the ends of the permanent wiring for Line 1, Line 2, Neutral (also strip ground wire on 4-Wire Connections). Tighten all 3 wire leads to the terminal block (Follow wire locations shown in Fig. 14).

Connections skip Steps 3 & 4 and continue with Step 5.

3.(4-Wire Permanent Connection ONLY) Disconnect the ground strap.

Remove the factory installed ground screw & plate to release the factory installed copper ground strap from frame of the appliance. Cut and discard the copper strap from the terminal block. KEEP the ground screw, ground plate and go to Step 4.

4. (4-Wire Permanent Connection ONLY) Connect the ground wire lead (Green) to the frame of the appliance using the ground screw & plate as shown in Fig. 15. Be sure to install using the same hole in the frame where the ground screw was originally installed.

5. (3 & 4 - Wire Permanent Connections) Make sure all connections are tightened securely and replace the rear access cover (See Fig. 9).

NOTE: Non-terminated field wire compression connections must be set at approximately 35 in./lbs.

5. CAREFULLY SLIDE RANGE INTO FINAL LOCATION.

Be sure to provide all the adequate clearances and dimensions shown in Figs. 1, 2 & 3 before moving range into final location.

Carefully slide range into final position while inserting rear leveling leg into and FULLY ENGAGING THE ANTI-TIP BRACKET (See Fig. 7). Make sure the power cord folds into the remaining open floor area behind the range Warmer or storage drawer. Be sure to check the level of the range.

Fig. 13

Fig. 14

Fig. 15

316454905 specifications

The Frigidaire 316454905 is a highly regarded oven range part designed to enhance the cooking experience in modern kitchens. This component serves as a replacement oven igniter, integral to the ignition process of gas ovens. Its primary function is to ensure that the gas flow ignites correctly, allowing for precise cooking temperature control and efficient burner operation.

One of the standout features of the Frigidaire 316454905 is its robust construction. Made from high-quality materials, this igniter is engineered to withstand the high temperatures typically found in cooking environments, ensuring longevity and reliability. This durability is especially important for households that frequently use their ovens, as an effective igniter can significantly improve the overall cooking experience.

The Frigidaire 316454905 employs advanced technologies that facilitate quick and safe ignition of the gas. The igniter glows bright orange when powered, providing a clear visual cue that it is functioning correctly. This mechanism not only enhances user convenience but also increases safety by preventing gas buildup before ignition, a critical aspect during cooking operations.

Another notable characteristic is its compatibility with a wide range of Frigidaire gas ovens. This versatility ensures that homeowners can easily find a replacement part that fits their specific oven model, thus simplifying the repair or replacement process. Moreover, its straightforward installation process makes it accessible for users who prefer to carry out DIY repairs. Many find that they can replace the igniter without professional assistance, saving both time and money.

Efficiency is another essential feature of the Frigidaire 316454905. By ensuring that the oven gases ignite quickly and efficiently, it enables better temperature control and consistent cooking results. Whether baking, broiling, or roasting, this igniter plays a crucial role in achieving perfectly cooked dishes.

In summary, the Frigidaire 316454905 is a key component for gas ovens, featuring durable construction, advanced ignition technologies, and compatibility with various models. Its efficiency and ease of installation make it a valuable part of any kitchen, ensuring that meals are prepared safely and effectively. For anyone seeking to enhance their cooking experience or needing a reliable replacement part, the Frigidaire 316454905 stands out as an exceptional choice.