Troubleshooting

ENGLISH

If a fault occurs, run through the points listed below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you repair the receiver yourself as this will invalidate the guarantee!.

PROBLEM

–POSSIBLE CAUSE REMEDY

NO POWER

–The AC power cord is disconnected. Connect the cord securely.

–Poor connection at the wall socket or the wall socket is inactive.

Check the wall socket using a lamp or another appliance.

NO SOUND FROM THE FRONT SPEAKERS

–Speaker cables are disconnected. Check the speaker connections.

–Volume is too low. Adjust the volume.

NO SOUND FROM THE REAR SPEAKERS

–Surround mode is switched off. Select a surround mode.

–Volume and rear level are too low. Adjust the volume.

–A monaural source is used.

Select a stereo or surround source.

–Dolby 3 Stereo mode is selected. Switch off Dolby 3 Stereo mode.

–Dolby Pro Logic source is not present.

Make sure that your video device is in the stereo mode.

NO SOUND FROM THE CENTER SPEAKER

–Dolby Pro Logic or Dolby 3 Stereo mode is not selected. Select Dolby Pro Logic or Dolby 3 Stereo mode.

–Volume and center level are too low. Adjust the volume and center level.

–The center mode is set to phantom mode. Set the center mode to normal or wide.

NO SOUND IS HEARD, EVEN WHEN INPUT SELECTION IS MADE

–The MUTE button is pressed.

Press MUTE again to cancel the MUTE function.

–Volume is too low. Adjust the volume.

–Connections between the components are incorrect. Make connections correctly.

THE REMOTE CONTROL UNIT DOES NOT OPERATE

–No batteries loaded or dead batteries. Replace the batteries.

–The remote sensor is obstructed. Remove the obstacle.

–No antenna connected. Connect an antenna.

–The desired station frequency is not tuned in. Tune in the desired station frequency.

–Antenna in wrong position. Move antenna and retry turning.

–Surrounding area causing interference. Lengthen or elevate antenna.

PRESET STATIONS CANNOT BE RECEIVED

–An incorrect station frequency has been memorized. Memorize the correct station frequency.

–The memorized stations are cleared. Memorize the stations again.

POOR FM RECEPTION

–No antenna connected. Connect an antenna.

–The antenna is not positioned for the best reception. Change the position of the antenna.

CONTINUOUS HISSING NOISE DURING FM RECEPTION, ESPECIALLY WHEN A STEREO BROADCAST IS RECEIVED

–Weak signal.

Change the position of the antenna.

Install an outdoor antenna. Use an antenna with 3, 4 or 5 elements if the broadcast station is far away.

CONTINUOUS OR INTERMITTENT HISSING NOISE DURING AM RECEPTION, ESPECIALLY AT NIGHT

–Noise is caused by motors, fluorescent lamps or lightning, etc.

Keep the receiver away from noise sources. Install an outdoor AM antenna.

A HUM CAN BE HEARD DURING AM RECEPTION

–The AC power cord may be too close to the AM loop antenna or the antenna wire.

Position the AC power cord away from the antenna wire and the AM loop antenna.

Adjust the position of the AM loop antenna.

OTHER SYSTEM COMPONENTS DO NOT REACT TO REMOTE CONTROL COMMANDS

–DIGI LINK III connections are not made properly. Make proper DIGI LINK III connections.

STATIONS CANNOT BE RECEIVED

RV-4060R specifications

The Sherwood RV-4060R is a remarkable addition to the world of high-fidelity audio receivers, designed to deliver an immersive listening experience. Known for its versatility and numerous features, the RV-4060R is an ideal choice for audiophiles and casual listeners alike.

One of the standout features of the Sherwood RV-4060R is its power output. The receiver is capable of delivering 60 watts per channel across a wide range of audio frequencies, ensuring that it can handle various speaker configurations while providing clear and powerful sound. Whether you're hosting a gathering or enjoying a quiet evening at home, the RV-4060R ensures that every note and beat is heard with clarity.

In terms of connectivity, the RV-4060R is equipped with multiple input options, including HDMI, optical, and coaxial inputs. This extensive range of connectivity allows users to easily link up a variety of devices, from gaming consoles to streaming devices and Blu-ray players. The inclusion of Bluetooth technology further enhances this model's versatility, allowing users to wirelessly stream their favorite music directly from smartphones, tablets, or computers.

The RV-4060R also supports various audio formats, including Dolby Digital and DTS, making it suitable for both movies and music. With built-in decoding capabilities, this receiver can effectively deliver cinematic sound quality, perfect for home theatre setups. The advanced signal processing ensures that dialogue is clear, while ambient sounds are represented with precision.

Additionally, the Sherwood RV-4060R comes with a user-friendly interface and a remote control, simplifying the navigation through different audio settings and sources. The sleek design and modern aesthetics blend seamlessly with any home décor, making it not just a functional device but also an attractive part of your entertainment center.

The receiver is built with durable and high-quality components, contributing to its long-lasting performance. It also incorporates protective circuitry to safeguard against overloads and short circuits, ensuring reliable operation.

In summary, the Sherwood RV-4060R stands out for its powerful performance, comprehensive connectivity options, support for surround sound formats, and user-friendly design. Whether you're a movie buff or a music lover, the RV-4060R is well-equipped to elevate your audio experience to new heights, proving to be a worthwhile investment for any home audio system.