Dacor RSE30, rsd30, MRES30 Verify Proper Operation for Electric Ranges RSE and Mres

NOTE:

Prior to operating the cooktop or oven sections of the range, please read the accompanying Use and Care Manual carefully. Important safety, service and warranty information is contained within this manual.

Re-installing the Oven Door

Grasp the oven door on opposite sides and lift it until the door hinges are aligned with the openings in the oven frame. Holding the door at about a 30˚ angle from the horizontal, slide the hinges into the openings until the bottom hinge arms drop fully into the hinge receptacles. Lower the door to the fully opened position, and then rotate the two hinge catches toward the oven. Open and close the door completely to ensure that it is properly installed. Peel off the protective layer of plastic that covers the door panel.

Verifying Proper Gas Operation of the Dual Fuel Ranges (RSD)

WARNINGS:

1.The range and shut-off valve must be disconnected from the gas supply piping during any pressure testing exceeding 1/2 psi (3.5kPa).

2.The range must be isolated from the gas supply piping by closing the shut-off valve during any pressure testing at or below 1/2 psi (3.5 kPa).

Before beginning the test procedure, ensure that all cooktop section control valves are in the “OFF” position, and all burner rings, burner caps, and grates are properly positioned on the top frame. Turn on the gas supply at the shut-off valve.

Turn on the power supply to the range. Set the time of day by pressing the “CLOCK” key and then pressing either of the “TIME•TEMP” keys (“+” or “-” keys) to advance or reduce the time in the display in the desired setting.

Test each top burner separately by pressing and turning one control knob at a time counterclockwise to the “HIGH” position. All ignitors will spark continuously, but only the burner with gas flowing to it will ignite. It will take approximately 4 seconds for ignition to occur, at which time the ignitors will stop sparking. If ignition does not occur within 4 seconds, turn off the knob, wait for at least 2 minutes to allow any gas to dissipate, then repeat this ignition test. The control knob can then be rotated, counterclockwise, from “HIGH” to “LOW” to adjust the flame height (size) progressively. Repeat the ignition test for all top burners.

When installed properly, the flame will be steady and quiet. It will also have a sharp, blue inner cone that will vary in length proportional to the

Verify Proper Operation for Electric Ranges (RSE and MRES)

For RSE range top, rotate one surface element knob at a time, counterclockwise, to the “HI” position. Within 5 seconds, the element should be fully energized and glowing red. Verify that the residual heat indicator light comes on in conjunction with the proper element, within approximately 30 seconds. Return the knob to the “OFF” position. Repeat for all surface elements. (Note: The right front element is a dual coil element. Clockwise rotation from “LO” to “HI” will energize the inner coil only. Counterclockwise rotation from “LO” to “HI” will energize both the inner and outer coils together).

For MRES range top, turn an element, tap the “ON/OFF” key then tap the slew up/down area of the desired element. The element will come on at a setting of the number touched and may be adjusted up or down by slewing up or down on the appropriate key area with your finger.

To activate the Dual Outer Element, tap the circle key at the end of the slew area (second row), then tap or slew your finger up or down on the second row of numbers. The outer ring element will come on at a setting of the number touched last. To turn the element off, tap the “ON/OFF” key. You may turn off all active elements at the same time by tapping twice on the “CANCEL•SECURE” key located below the controls

NOTE:

When the MRES unit is powered on for the first time, the cooktop control will go through a self- check routine. When the self- check is complete, the cooktop control will go to SECURE mode. See Use and Care Manual for Secure Mode instructions.

Within 5 seconds, the element should be fully energized and glowing red. Verify that the residual heat indicator light comes on in conjunction with the proper element, within approximately 30 seconds.

RSD Dual-Fuel Range Control Knob

RSE Range Control Knob

ON/OFF

ON/OFF

ON/OFF

ON/OFF

CANCEL • SECURE

MRES “SLEW UP/DOWN” Range Control

NOTES:

If either the oven or cooktop does not operate properly, follow these troubleshooting steps:

1.Verify that power (all ranges) and gas (RSD) are supplied to the range.

2.Check the electrical connections (all ranges) and gas (RSD) supply to ensure that the installation has been completed correctly.

3.Repeat the above burner ignition test (RSD).

4.If the appliance still does not work, contact an authorized DACOR service company at (800) 772-7778. Do not attempt to repair the appliance yourself. DACOR is not responsible for service required to correct a faulty installation.