GE JGAS02PN, JMS02PN, JGAS02EN manual Oven Control, Oven Shelves, SheM Positions

Page 11

Oven Control

Your oven is controlled by an OWN TE~ knob. It will norrndly take 30-90 seconds before the flame comes on.

After the oven reaches the selected temperature, the oven burner cycles+ff completely, then on with a full flame-to maintain the selected temperature.

Air Adjw@ent

An air adjustment

 

 

 

 

 

 

 

&

 

 

shutter for the

 

 

.,’ /

oven burner

—

,..

,.’.-

regulates the flow

 

. . .

 

 

 

 

of air to the flame.

 

 

 

 

 

 

You’ll find the

Loosen

‘+

shutter against the

 

 

/

 

 

 

back wdl behind

 

 

 

 

 

 

Air

the broiler drawer.

 

 

adjustment

To reach it remove

ti shutter

the oven bottom (see the Care and Cleaning section) and the burner btie.

To adjust the flow of tir, loosen the Philhps head screw and rotate the shutter to allow more or less air into the burner tube as needed.

men the tight amount of Ar flows kto the burner, the flame should be steady, with approximately 1/2 inch blue cones, and should not extend out over the btie edges.

Oven Shelves

The shelves are des~ed tith stop-lock so when placed correctly on the sheM suppo~, they till stop before co~ng completely out of the oven and fi not tit when you are remotig food from them or plachg food on them.

men placing cookware on a shelf, pull the shelf out to the “stop” position. Place the cookwme on the shelf, then slide the shelf back into the oven.

This will elimimte reaching into the hot oven.

To remove a sheti

 

from the oven, pull

6

it toward you, tit

-1

the front end

 

upward and pull

*1- Iill

the shelf out.

To replace, place the shelf on the shelf support with the top-locks (curved extension of the shel~ facing up and toward the rear of the oven. Tilt up the front and push the shelf toward the back of the oven until it goes past “stop” on the oven wall. Then lower the front of the shelf and push it dl the way back.

SheM Positions

The oven has 4 she~ supports for normal baking and roasting identified in this illustration as A ~ottom), B, C, D (top).

Shelf positions for cooking are suggested on the Baking, Broiling and Roasting pages.

(continued ne~page)

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Gas Range ~ you received a damaged rarige Save time and money. Before you Requ=t serviceRead this book carefdy Write dom the model and serial numbersDo not zttempt to or rephee ay Phg your ~~ into a l~volt ~undedNever pickup ating pan. Turn off Stiace CMQKeep fl p~es away from top buraers Mti when you clean the cooktop becauseFoods for- shotid be as dry as possible Ka cornbtiation of & or fa~ ~ be usedPage 14, 15 Before Lighting a Burner Lighting Instructions for Electric Ignition Models JGAS02ENSurface Burner Controls Top of Range Cookware How to Select Name SbeTo Light a Surface Burner After Lighting a Burner Air Adjw@entLighting htructions for Stiding mot Models Before Using Your OvenPower Outige Lighting Instructions for Electric Ignition Model JGAS02ENSheM Positions Oven ControlOven Shelves Do Zt Yourse~-Adjmt the Oven Themosbt Oven VentsBaKng Pans How to Set Your Range For BatingPan Placement PreheatingAltinu Fofl Bahg GuidesCooties CakesFrozen Romk Questions and Answers Questiom & Amwers How to BrotiUse of Altim Foti BRO~~G G~E Lift-Up/Off Cooktop How to Remove the Range for Cleaning and ServicingBurners CA~ ~ ClehgControl Panel and mobs Burner GratwTo remove Men the broiler is cool, remove the rack and pan Removable Oven BotiomBroiler Drawer To removeOutside of door Brofler Pan and RackOven Door Inside of door Soap and water ti normally do the jobMeti Pafi Porceltin Oven htefiorOpen tidom Before YOU Begin~R HWG ~G LMW~ANT WHY lHSTRU~IOHS~KGUMD lHfiMWTIOH ~e InsMation LPG Do not USE AN -NSION Cord m ~S Appwce ~A~~~N~~O&~=A ~ toLight MD Wjust Surwe Burner PILO~ Cone of at least 3/4 inch. Turn valve knob When ml HOOKU~ ~E ~MPLETED Consumer information center USE this Problem SolverWdll Be There 800~432-2737 WARRAN~

JGAS02PN, JGAS02EN, JMS02PN specifications

The GE JMS02PN, JGAS02EN, and JGAS02PN are advanced gas turbine products developed by General Electric, renowned for their application in various energy and industrial sectors. These turbines represent cutting-edge engineering and design, focusing on delivering high efficiency, reliability, and sustainability.

The JMS02PN model is notable for its performance in power generation applications. With a significant output capacity, it is designed to operate efficiently across a wide range of conditions. Its advanced aerodynamics and combustion technologies allow for reduced emissions while maximizing fuel efficiency. The turbine also features a sophisticated control system that optimizes performance in real-time, ensuring that it can adapt to varying load demands.

Moving on to the JGAS02EN model, this turbine is engineered for enhanced environmental performance. It incorporates GE’s innovative dry low NOx combustion technology, which minimizes nitrogen oxide emissions, making it compliant with stringent environmental regulations. The JGAS02EN is suitable for both industrial and commercial applications due to its flexibility and scalability, allowing users to implement it in diverse operational contexts.

Similarly, the JGAS02PN shares several characteristics with the JGAS02EN but is tailored for specific industrial needs. The JGAS02PN is designed to operate in more challenging environments, offering exceptional durability and long service intervals. This model features advanced materials and coatings that withstand high temperatures and corrosive conditions, ensuring reliability and longevity in operation.

All three models leverage advanced technologies such as digital twin simulations and predictive maintenance capabilities, enabling operators to monitor performance accurately and perform proactive interventions. This technology ensures not only efficiency but also a significant reduction in downtime, leading to lower operational costs.

In summary, the GE JMS02PN, JGAS02EN, and JGAS02PN turbines exemplify the pinnacle of gas turbine technology. They are designed to meet the demands of today's energy landscape, emphasizing performance, sustainability, and adaptability. With their innovative features and robust construction, these turbines are set to play a pivotal role in the future of power generation and industrial applications. Whether aiming for high efficiency, lower emissions, or superior durability, these models offer unparalleled solutions for modern energy challenges.
Top Page Image Contents