GE JGAS02EN, JMS02PN, JGAS02PN manual Removable Oven Botiom, Broiler Drawer, To remove

Page 22

CAm ~ CLE-G

(continued)

Removable Oven Botiom

The oven bottom can be removed to make cleaning easier. Make sure the oven is completely cool.

To remove:

1.Loosen (but do not remove) the 2 screws at the front of the oven bottom.

2.Slide the screws back to release the front of the oven bottom.

3.Lift tie oven bottom up ad pull forward until the rear tabs release from the back wd.

4.Take the oven bottom out of the oven.

To replace the oven bottom:

1.hsert the tabs into the slots in the rear of the oven wall.

2.Slide the 2 screws at the front of the oven bottom forward and tighten them to secure the oven bottom in place.

NOTE: If the oven bottom is replaced incorrectly, it may warp and cause undesirable baking results.

The oven bottom has a porcelain enamel ftih. To make cleaning easier, protect the oven bottom from excessive spi~overs. This is particularly important when baking a fruit pie or other foods with high acid content. Hot fruit fi~ings or foods that are acid in content such as mik, tomato or sauerkraut, and sauces with vinegar or lemon juice, may cause pitting and damage to the porcelain enamel surface.

To protect the oven bottom surface, place a piece of durninum foil stightiy larger than the baking dish on the shelf below to catch any boilovers. It should not completely cover the shelf as this wotid cause uneven heat in the oven. Aluminum foil should not be placed on the oven bottom.

Ma spflover d~ occur on the oven bottom,

allow the oven to cool fust. You can clean the bottom with soap and water, a mild abrasive cleanser, soap- filled abrasive pads or an oven cleaner following package directions.

Broiler Drawer

To remove:

1.men the broiler is cool, remove the rack and pan.

2.Pull the broiler drawer half-way out. WU the metrd clip located in the center of the drawer bottom upward as far as it will go (abut 2 inches). Pull the drawer dl the way out of the compartment.

3.Clean the broiler drawer with hot soapy water.

To replace:

1.Slide the broiler drawer onto the guide rails at the sides of the broiler compartment. Push the drawer until completely closed.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Gas Range Write dom the model and serial numbers Save time and money. Before you Requ=t serviceRead this book carefdy ~ you received a damaged rarigePhg your ~~ into a l~volt ~unded Do not zttempt to or rephee ayStiace CMQ Never pickup ating pan. Turn offKa cornbtiation of & or fa~ ~ be used Mti when you clean the cooktop becauseFoods for- shotid be as dry as possible Keep fl p~es away from top buraersPage 14, 15 Surface Burner Controls Lighting Instructions for Electric Ignition Models JGAS02ENBefore Lighting a Burner Air Adjw@ent How to Select Name SbeTo Light a Surface Burner After Lighting a Burner Top of Range CookwareLighting Instructions for Electric Ignition Model JGAS02EN Before Using Your OvenPower Outige Lighting htructions for Stiding mot ModelsOven Shelves Oven ControlSheM Positions Oven Vents Do Zt Yourse~-Adjmt the Oven ThemosbtPreheating How to Set Your Range For BatingPan Placement BaKng PansCakes Bahg GuidesCooties Altinu FoflFrozen Romk Questions and Answers Use of Altim Foti How to BrotiQuestiom & Amwers BRO~~G G~E How to Remove the Range for Cleaning and Servicing Lift-Up/Off CooktopCA~ ~ Clehg BurnersBurner Gratw Control Panel and mobsTo remove Removable Oven BotiomBroiler Drawer To remove Men the broiler is cool, remove the rack and panInside of door Soap and water ti normally do the job Brofler Pan and RackOven Door Outside of doorPorceltin Oven htefior Meti PafiBefore YOU Begin Open tidomLMW~ANT WHY lHSTRU~IOHS ~R HWG ~G~KGUMD lHfiMWTIOH ~e InsMation LPG ~A~~~N~~O&~=A ~ to Do not USE AN -NSION Cord m ~S AppwceLight MD Wjust Surwe Burner PILO~ Cone of at least 3/4 inch. Turn valve knob When ml HOOKU~ ~E ~MPLETED USE this Problem Solver Consumer information centerWdll Be There WARRAN~ 800~432-2737

JGAS02PN, JGAS02EN, JMS02PN specifications

The GE JMS02PN, JGAS02EN, and JGAS02PN are advanced gas turbine products developed by General Electric, renowned for their application in various energy and industrial sectors. These turbines represent cutting-edge engineering and design, focusing on delivering high efficiency, reliability, and sustainability.

The JMS02PN model is notable for its performance in power generation applications. With a significant output capacity, it is designed to operate efficiently across a wide range of conditions. Its advanced aerodynamics and combustion technologies allow for reduced emissions while maximizing fuel efficiency. The turbine also features a sophisticated control system that optimizes performance in real-time, ensuring that it can adapt to varying load demands.

Moving on to the JGAS02EN model, this turbine is engineered for enhanced environmental performance. It incorporates GE’s innovative dry low NOx combustion technology, which minimizes nitrogen oxide emissions, making it compliant with stringent environmental regulations. The JGAS02EN is suitable for both industrial and commercial applications due to its flexibility and scalability, allowing users to implement it in diverse operational contexts.

Similarly, the JGAS02PN shares several characteristics with the JGAS02EN but is tailored for specific industrial needs. The JGAS02PN is designed to operate in more challenging environments, offering exceptional durability and long service intervals. This model features advanced materials and coatings that withstand high temperatures and corrosive conditions, ensuring reliability and longevity in operation.

All three models leverage advanced technologies such as digital twin simulations and predictive maintenance capabilities, enabling operators to monitor performance accurately and perform proactive interventions. This technology ensures not only efficiency but also a significant reduction in downtime, leading to lower operational costs.

In summary, the GE JMS02PN, JGAS02EN, and JGAS02PN turbines exemplify the pinnacle of gas turbine technology. They are designed to meet the demands of today's energy landscape, emphasizing performance, sustainability, and adaptability. With their innovative features and robust construction, these turbines are set to play a pivotal role in the future of power generation and industrial applications. Whether aiming for high efficiency, lower emissions, or superior durability, these models offer unparalleled solutions for modern energy challenges.
Top Page Image Contents