Bosch Appliances HGS255UC, HGS246UC, HGS256UC, HGS247UC manual Fled service agency in accordance with

Thiskit isusedto convertonlydualfuelranges(model# HDS252U,HDS255UandHDS256U)andgasranges(model# HGS232UC,HGS236UC,HGS242UC,HGS245UC,HGS246UC,HGS247UC,HGS252UC,HGS255UC,HGS256UC),fromnaturalgas

operationto propanegasoperationThiskitcannotbeusedtoconvertotherBoschmodelrangesorotherbrandranges..The modelnumberonyourrangeisstampedontheplatebehindthewarmingorstoragedrawer.

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. Savethe natural gas parts for possibleconversion from LP

back to natural gas in the future.

PLFJ_E READ INSTALLA_ON INSII_UCT%ON$ BEFORE BE431NNINGTHE CONV£RSION.

f

This conversion kit shall be installed by a quali o

fled service agency in accordance with the

manufacturer's instructions and all applicable

codes and requirements of the authority having jurisdiction, If the information in these instruc o tions is not followed exactly, a fire, explosion

or production of carbon monoxide may result

causing property damage, personal injury or

loss of life, The qualified service agency is reo sponsible for the proper installation of this kit, The installation is not proper and complete uno til the operation of the converted appliance is checked as specified in the manufacturer's ino structions supplied with the kit,

_J

High Altitude Installation:

For conversion in areas above 2,000 feet, contact Bosch service for instructions: 800=944=2904.

F For Massachusetts Installations:"

:[.Installation must be performed by a qualified or licensed contractor, plumber or gas fitter qualified or licensed by the state, province or region where this appliance is being installed.

2.Shut=off valve must be a "T" handle gas cock.

3.Flexible gas connector must not be longer than 36 inches.

Kit Contents,

Conversion Kit Instructions

Conversion Sticker

4 LPOrifices (:[=70/:[=86/:[=:[0:[/:[=:[:[6)

Tools Required:

7 mm Socket Driver wi 3" extension

Torx (T20)=head screwdriver

Adjustable Wrench

Flat:head Screwdriver (:[/8" or smaller)

Phillips Head Screwdriver

_ CAUT][ON:

(!)When connecting theunit to the propane gas, make certain the propane gas tank is equipped with its own high pressure regulator. In addition, a pressure regulator was supplied with the range. This second regulator must be installed with the range. The maximum gas pressure to this appliance is not to exceed :[4.0 inches water col= umn from the propane gas tank regulator,

The following must be met when testing supply piping system:

a)The appliance and its individual shut-off valve must be disconnected from the gas supply piping system at test pressures in excess of :[/2 psig (3.5 kPa).

b)The appliance must be isolated from the gas supply piping system by closing its individual manual shut- off valve during any pressure testing of the gas sup- ply piping system at test pressures equal to or less than :[/2 psig (3.5 kPa).

Always Provide Adequate Gas Supply

The Bosch Freestanding Dual Fuel and Gas Ranges are shipped from the factory for use with natural gas. Use this kit to con= vert the appliance for LPgas use if necessary.

,Be sure the range is converted for use with the appropri= ate gas before using it.

,Your range is designed to operate at a pressure of :[0" of water column when used with LPgas.

,When checking for proper operation of the regulator, the inlet pressure must be at least :[" greater than the operat= ing (manifold) pressure above. When converting for LP gas use, the pressure supplied to the regulator must be between :[:[" and :[4" of water column. See step 2 "Convert Pressure to Regulator from 5" to :[0" W,C.", next page.

,The pressure regulator located in the inlet of the range manifold must remain in the supply line.

oUse a flexible metal appliance connector to connect the range to the gas supply. The connector should have an [.D. of :[/2" and be 5'in length. In Canada, the connector must be single wall metal and no longer than 6: