![](/images/new-backgrounds/1089412/894123x1.webp)
ALLURE® QS2 SERIES RANGE HOOD
PREPARE HOOD LOCATION
ROOF CAP | 3¼" X 10" or |
| 7" ROUND DUCT |
| (For vertical |
| discharge) |
SOFFIT |
| |
| HOUSE WIRING | |
CABINET | (Top or Back of hood) | |
| WALL CAP | |
HOOD |
| |
24" - 30" ABOVE | 3¼" X 10" DUCT | |
COOKING SURFACE | ||
(For horizontal discharge) | ||
| ||
1 Determine whether hood will discharge vertically (3¼” x 10” | ||
or 7” Round), or horizontally (3¼” x 10” only). For vertical or | ||
horizontal discharge, run ductwork between the hood location | ||
and a roof cap or wall cap. For best results, use a minimum | ||
number of transitons and elbows. |
| |
2 Use diagrams, below, for proper placement of ductwork and | ||
electrical cutout in cabinet or wall. For a | ||
tion, DO NOT cut a duct access hole. |
HOOD MOUNTING SCREWS (4) | 3¼” X 10” | ||||
VERTICAL DUCTING | |||||
1315/16" (30" hood) |
| ||||
1315/16" (30" hood) |
| ||||
1615/16" (36" hood) |
| ||||
1915/16" (42" hood) | 1615/16" (36" hood) |
| |||
CABINET FRONT | 1915/16" (42" hood) |
| |||
|
| 7½" |
|
| |
| CABINET BOTTOM |
|
| ||
| 5¼" | 5¼" | 2" | 10½" | |
| VERTICAL DUCT | ||||
|
| ||||
|
|
| |||
5" | ACCESS HOLE |
|
| ||
1¼" |
|
| 1½" | ||
|
|
|
|
|
|
| ELECTRICAL |
|
| |
|
|
|
|
| |||
WOOD SHIMS |
|
| ACCESS HOLE | ||||
CENTER | |||||||
(in cabinet bottom) | |||||||
LINE | |||||||
cabinets only) |
|
|
| ||||
|
|
|
|
| |||
|
|
|
| ||||
WOOD SHIMS |
|
| 3¼” X 10” | ||||
|
| HORIZONTAL DUCTING | |||||
cabinets only) |
|
| |||||
CABINET FRONT | |||||||
|
|
|
| 1/8" ¾" |
|
|
3¾" | HORIZONTAL DUCT |
| ||
ACCESS HOLE |
| |||
CABINET |
| |||
5¼" | 5¼" |
| ||
BOTTOM |
| |||
1315/16" (30" hood) | 7½" |
| ||
1315/16" (30" hood) | ||||
1615/16" (36" hood) | ||||
1615/16" (36" hood) | ||||
1915/16" (42" hood) | ||||
1915/16" (42" hood) | ||||
HOOD |
| |||
|
| ELECTRICAL | ||
MOUNTING | CENTER | |||
ACCESS HOLE | ||||
SCREWS (4) | LINE |
| ||
| (in wall) | |||
|
| |||
|
|
|
Page 2
PREPARE HOOD LOCATION
7” ROUND
VERTICAL DUCTING
3 Run house wiring between service panel and hood location.
PREPARE THE HOOD
7” ROUND
DUCT PLATE
1Remove 7” Round Duct Plate from top of hood. Set duct plate aside - with mounting screws.
FILTERS ![](/images/new-backgrounds/1089412/894123xi4.webp)
2 Remove tape holding Filters in place. Pull down on filter tabs or finger holes and lift filters out. Set filters aside.