Assembly | Harman Stove Company MARK III instruction

Installation

2.3 Assembly.

Slide the blower into the slotted bracket on the rear of the stove. The blower will rest at the bottom of the slot.

The shaker handle bolts onto the shaker block using the bolts and lock washers provided.

The draft control is bolted through the hole in the center of the ash door as shown below. The knob should spin freely and open to a distance of about 1/4 inch from the door surface, while being able to close against the face of the door.

The viewing glass is installed between the door and the window frame. The glass gasket is installed only on the sides of the glass panel. The top and bottom of the glass are open to provide air-wash and secondary air to the firebox. The glass frame is secured to the door with four bolts.

The Mark II and Mark III also have a top trim piece which bolts onto the top of the door.

Be sure the frame bolts and trim bolts are secured.

2.4GENERAL INFORMATION. Installation Checklist:

A. Have your stove installed by a trained installer. Preferably one who is certified by the National Fireplace Institute or similar certification agency.

B. Before starting Installation, check for proper clearance to combustibles where the stove is going to be located.

C. Never vent a solid fuel burning appliance into a flue serving another appliance.

D. Have the chimney inspected and thoroughly cleaned. Inspect that it is a Class “A” chimney either masonry or factory built. If it is a manufactured chimney, ensure that it is installed as per the manufacturers requirements. Be sure that the chimney is tall enough. Solid fuel chimneys fall under a general rule, 16 ft. minimum height, 2 ft. taller than anything within 10 ft., and 3 ft. above where it passes through the roof line. The chimney must be capable of a minimum .06 inches of water column of draft when the stove is burning.

E. Limit the amount of connector pipe. Position the stove as close to the flue as possible. (8 ft. or less)

No more than two 90° elbow fittings should be used.

Any horizontal connector pipe should have at least 1/4 in. of rise per foot in length. A barometric damper may be installed to prevent excessive or erratic draft.

MANUAL DAMPERS OR “HEAT SAVERS” MUST NEVER BE INSTALLED IN THE FLUE PIPE. IMPROPER OPERATION COULD RESULT IN DEATH.

Magnafire Series Coal Stoves

3-90-70746R8_11/12

MARK II, MARK I, MARK III specifications

Harman Stove Company has established itself as a leader in the production of high-quality wood and pellet stoves. The MARK III, MARK I, and MARK II series represent some of the finest offerings from this esteemed company, showcasing impressive features, innovative technologies, and unique characteristics that cater to a variety of heating needs.

The Harman MARK III is renowned for its robust construction, offering a substantial heat output that can effectively warm larger spaces. One of its standout features is the patented "Smart Heat" technology, which ensures optimal fuel efficiency and consistent heat distribution. The MARK III incorporates a large combustion chamber, capable of accommodating various types of pellets or wood, which enhances its versatility. Additionally, the unit's automatic ignition system simplifies operation, allowing users to easily start a fire with the push of a button. The intense heat produced is further complemented by a sleek design that fits seamlessly into any decor.

The Harman MARK I is designed for those seeking a compact but powerful heating solution. Despite its smaller size, this stove is engineered for maximum efficiency with an efficient burn rate that translates to lower emissions and reduced environmental impact. It features a ceramic glass door that provides a pleasing view of the fire while retaining heat. The MARK I also includes Harman's advanced feed system that ensures steady fuel delivery, optimizing performance and reducing the need for frequent refueling. This model is perfect for small homes or cabins, where space is at a premium but warmth is essential.

The MARK II combines the best of both worlds, offering a balance between size and output. This model incorporates advanced airflow technologies that enhance combustion efficiency and minimize soot buildup. Its flexible installation options make it suitable for a variety of spaces, and its user-friendly digital control panel allows for effortless adjustments to temperature settings. Like its counterparts, the MARK II ensures a clean burn, contributing to improved air quality.

Overall, the MARK series from Harman Stove Company showcases the commitment to delivering reliable, efficient, and aesthetically pleasing heating solutions. With advanced technologies, user-centric designs, and exceptional performance, each model provides a unique blend of features that cater to diverse heating needs, ensuring a cozy and comfortable environment for any home.