Connections, PRE-LIGHTING Checks | Kuma Stoves SHASTA manual

To provide correct pressure of the fuel supply to your stove, the tank outlet should be between 16” and 72” above the carburetor on the stove. Be sure the support system under the tank is safe and adequate as a full 300 gallon tank will weigh about 2000 lb.

If you must install a tank below the stove, or above the recommended height, a lift pump and/or a level control valve may be needed. You will need to check local building codes regarding such installations.

CONNECTIONS:

There should be 2 valves on a typical installation: 1) a shut-off valve at the tank to allow service to any piping or changing the main filter, and 2) a shut-off valve close to the stove to be able to isolate the stove for any maintenance, and if required by code, a fire valve right before the fuel pipe enters the building which would automatically shut off the oil supply in the unlikely event of the stove overheating. Piping to the stove from the tank may be either steel or copper, but copper is preferred to prevent any rusting problems. When making the fuel line connection with the copper line from the tank to the stove, it is best to have a gradual slope or “fall” on the line (i.e. no dips or kinks) so as to prevent any air bubbles or collection of dirt or other impurities. A 3/8” diameter copper supply line is recommended and either compression type or flare type fitting may be used. Finally, a good quality filter should be placed at the tank to ensure a good, clean supply of oil to your stove. The carburetor on the stove is equipped with a screen-type filter but it is not intended for use as the primary filter.

SECTION 4

Lighting, carburetor adjustments, and draft stabilizer adjustments

PRE-LIGHTING CHECKS:

The installation should be inspected to ensure that the work is complete and the workmanship is satisfactory. No stove should be lit if any part of the installation does not comply with the relevant standards and regulations.

The oil tank should be examined to confirm there is a supply of the correct grade of oil, that a filter and a working isolation valve are fitted. Having verified that the oil pipe work up to the stove is complete and that the fire valve (if used) is closed, the tank isolation valve should be opened and the pipe work inspected for leaks. The pipe into the inlet of the carburetor should be uncoupled, the fire valve (if used) opened and a minimum of one quart of oil collected into a suitable receptacle. If dirt or water is present in this sample, additional oil should be allowed through the pipe work until it is free from contaminates. The fuel pipe work should be reassembled and all connections checked for leaks and tightened as necessary.

Top burn ring: Laying on top of the catalyst inside your Shasta stove is a stainless steel top burn ring. It is important that the ring be in the proper position. It comes in the proper position from the factory. Should the height of this ring change, it is easy to re-adjust by bending the three tabs that rest on the catalyst top up or down . Locate the two continuous rows of air holes circling the burner top. The top ring tabs should set on the catalyst top so that the outer edge of the ring comes out right between those two rows of air holes. It is also very important that the “cupped” part of the ring itself is facing up. The stove will not burn properly if the ring is face down.

SHASTA specifications

The Kuma Stoves SHASTA is a premium wood stove that exemplifies contemporary design and engineering excellence. Renowned for its extraordinary heat output and efficiency, the SHASTA is a perfect addition to any home seeking both style and functional warmth. With a commitment to sustainability, Kuma Stoves has ensured that the SHASTA meets stringent EPA standards, making it an eco-friendly choice for heating.

One of the standout features of the SHASTA is its exceptional heat output, which can efficiently warm large spaces. With a heating capacity of up to 2,500 square feet, it caters to the needs of various homes, ensuring comfort during the cold winter months. The stove boasts a burn time of up to 10 hours, allowing for longer intervals without the need for constant replenishment of fuel, enhancing convenience for homeowners.

The SHASTA is equipped with Kuma’s advanced clean burning technology, which maximizes efficiency while minimizing emissions. This technology utilizes secondary combustion, where smoke and gases are ignited above the fire, thus ensuring that the wood burns more completely. This not only results in less smoke but also reduces the environmental impact, allowing users to enjoy a cleaner, healthier heating option.

In terms of design, the SHASTA embodies a sleek, modern aesthetic that can seamlessly integrate into various home decor styles. It features a large viewing window framed by a robust cast iron door, allowing for a captivating view of the flames. This design element not only enhances the ambiance of any room but also showcases the craftsmanship that goes into each stove.

Durability is a hallmark of the SHASTA, built with heavy-duty steel and cast iron components that promise longevity. The stove is rigorously tested to ensure it can withstand high temperatures and continuous use, providing homeowners with peace of mind regarding their investment.

The SHASTA also includes convenient features such as an easy-to-use ash removal system, allowing for simple maintenance and upkeep. Its adjustable air control enables users to regulate the heat output, providing customized comfort depending on the weather and personal preferences.

In summary, the Kuma Stoves SHASTA combines impressive heating capabilities with advanced technologies and stylish design. Whether for cozy evenings or efficiently warming larger spaces, this wood stove represents a dependable, eco-friendly, and aesthetically pleasing choice for modern homes.