Freestanding and Undercounter Installation

Freestanding and Undercounter Installation

NOTE: Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and local codes and ordinances.

Tools needed

Gather the required tools and parts before starting installation.

■	Level	■	Pliers
■ Phillips No. 2 screwdriver		■	⁵⁄₁₆" Box-end wrench
■	Tape measure	■	Scissors
■	Flat-blade screwdriver	■	Utility knife

IMPORTANT:

■Do not grasp control panel to move compactor.

■Slide compactor onto cardboard or hardboard before moving compactor across floor to avoid floor covering damage.

■Do not allow the rear frame of the compactor to touch the floor covering when lifting or moving compactor.

Undercounter Installation

NOTE: Installation hardware is not provided. See “Accessories” for ordering conversion kit.

1.Measure the height of your kitchen cabinet opening. The top of the compactor should be at least ¹ " (3 mm) from the top of the kitchen cabinet opening.

The rear wheels are preset for a kitchen cabinet opening height of 34¹⁄₄" (87 cm) (position 1).

To adjust for other kitchen cabinet opening heights:

■Loosen self-tapping screw just enough to clear stud from hole in position 1.

■Move the rear wheel and stud to position 2 or 3 as needed for your kitchen cabinet opening measurement:

Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)

Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)

NOTE: To level the unit in position 3, you may need to add shims under the front leveling legs.

■Tighten screw. Repeat for other rear wheel.

Freestanding Installation

1.Use pliers to lower leveling legs away from cabinet. With the drawer still removed from the compactor cabinet, place level inside on the floor of the cabinet. Check that the compactor is level from front to back and side to side. Adjust the leveling legs until the compactor is level.

2.Move the compactor close to its final position.

3.Plug into a grounded 3 prong outlet.

4.Slowly move compactor into its final position. Check that compactor is still level. Repeat Step 1 if necessary.

5.Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check to see whether drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” later in this section, for further instructions.

A. Wheel bracket assembly

B. Compactor cabinet

C. Locating stud

D.Self-tapping screw (pivot)

2.Use pliers to lower leveling legs away from compactor cabinet. Adjust legs so there will be a ¹⁄₈" (3 mm) to ¹₄ "

(6.4 mm) space between the top of the compactor and the top of the kitchen cabinet opening. Stand the compactor upright.

3.Remove the plastic plugs from the compactor cabinet top.

4.Move the compactor close to its final position.

5.Plug into a grounded 3 prong outlet.

6.Determine whether you want the compactor cabinet or drawer front flush with the kitchen cabinet face.

Using 2 - #8 - 18 x ⁵₁₆ " mounting screws (provided in conversion kit), attach the retaining brackets (provided in conversion kit) to the compactor cabinet top as needed. See “Accessories.”

NOTE: Installation hardware is not provided with full cabinet models. See “Accessories” for ordering conversion kit.

■If the compactor cabinet face is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “1.”

■If the compactor drawer front is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “3.”

MTUC7000AWS, W10190314A specifications

The Maytag W10190314A, a component of the MTUC7000AWS laundry series, is a premium stackable washer and dryer that combines efficiency with cutting-edge technology and robust features. Designed for those who value both form and function, this unit is ideal for compact spaces without compromising on performance.

One of the standout features of the Maytag MTUC7000AWS is its high-efficiency washing capability. The unit employs a powerful motor that enables it to handle larger loads while using less water and energy. This not only reduces your utility bills but also lessens the environmental impact, aligning with sustainable living ideals.

A key technology integrated into this washer is the PowerWash cycle. This intelligent system is designed to tackle the toughest stains and dirt. It combines a robust wash action with prolonged wash times, ensuring that clothes come out cleaner than ever. Additionally, the washer's Advanced Vibration Control technology minimizes noise and vibrations, making it a perfect choice for apartments or homes where quiet operation is necessary.

Another notable characteristic of the MTUC7000AWS is its user-friendly interface. Equipped with a digital display and intuitive controls, users can easily select from multiple wash settings, tailoring cycles to their specific needs. The unit includes various preset cycles for delicates, bulky items, and more, providing versatility for varying fabric types.

The design of the Maytag MTUC7000AWS reflects both elegance and practicality. With a sleek finish and compact dimensions, it fits seamlessly into small laundry areas while still offering a large capacity. It also features a durable build quality, known to stand the test of time, ensuring that customers receive reliable performance for years to come.

Additionally, the Maytag brand is synonymous with dependability, backed by a robust warranty and customer service support. The washer is engineered with the latest technology that enhances its longevity, including a stainless steel drum that resists chipping and snagging.

In summary, the Maytag W10190314A in the MTUC7000AWS model stands out for its high efficiency, advanced stain-fighting features, user-friendly interface, and durable construction, making it an exceptional choice for those seeking a high-quality laundry solution in a compact form factor.