Maytag MTUC7000AWS manual Changing the Custom Panel, Countertop mounting, Cabinet-face mounting

Page 7

■If the compactor is to be midway between “1” and “3,” place the retaining bracket mounting screws through “2.”

A

B

3 2 1

A.Countertop

B.Retaining bracket (provided in conversion kit)

7.Slowly lift the front slightly and roll compactor into the kitchen cabinet opening.

8.Using 2 - #8 - 18 x ¹₂ " mounting screws (provided in conversion kit), fasten the retaining brackets (provided in conversion kit) to the countertop with the mounting screws.

Countertop mounting

A

B

C

A.Countertop

B.Retaining bracket (provided in conversion kit)

C.Mounting screw (provided in conversion kit)

NOTE: If retaining brackets cannot be attached to the underside of countertop, attach mounting clips (provided in conversion kit) to retaining brackets. Fasten compactor to kitchen cabinet face with mounting screws through the mounting clips.

Cabinet-face mounting

A C

B

D

9.Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check to see whether drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” later in this section, for further instructions.

Adjusting the Toe Plate

If the toe plate rubs the floor covering, the toe plate clearance may be changed as follows:

1.Mark on each side of the toe plate the amount of toe plate that rubs the floor covering.

2.Remove the drawer from the unit. See Step 3 in the “Unpacking” section.

3.Use a ruler and a pencil or chalk to draw a line between the marks on each side of toe plate.

4.Use scissors or utility knife to cut toe plate along line.

5.Replace drawer. If toe plate still rubs floor covering, repeat steps 1-4.

Changing the Custom Panel

Custom Panel with Handle

Dimensions

Use these dimensions drawings to create a custom panel for use without a trim kit. The panel should be ¹⁄₂" to ⁵⁄₈" (13 mm to

16 mm) thick.

NOTE: A thicker panel may need rounded front corners and a cutout for access to the handle.

23¹³⁄₁₆"

(60.5 mm)

15" (38.1 mm)

A. Mounting clip (provided in conversion kit) B. Kitchen cabinet

C. Retaining bracket (provided in conversion kit) D. Mounting screw (provided in conversion kit)

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Compactor Table of Contents Your safety and the safety of others are very important Compactor SafetyUnpacking Installation InstructionsElectrical Requirements Location RequirementsTools needed Freestanding and Undercounter InstallationUndercounter Installation Freestanding InstallationCountertop mounting Adjusting the Toe PlateCustom Panel with Handle Dimensions Changing the Custom PanelCustom Panel without Handle Dimensions InstallationHow Your Compactor Works Compactor USEStarting Your Compactor Using Solid Locked CycleLoading QuietSeries Sound PackageTo use the filter Using the Air Filter or FreshenerInstalling a New Bag Removing a Filled BagChanging the Air Filter or Freshener Cleaning Exterior SurfacesCleaning Inside the Drawer Compactor CareCleaning the Ram Cleaning Inside the CabinetCleaning Before a Vacation There is not enough compaction or force TroubleshootingYour compactor won’t operate Drawer won’t openCanada Assistance or ServiceAccessories U.S.ALimited Warranty Maytag Major Appliance Warranty

MTUC7000AWS, W10190314A specifications

The Maytag W10190314A, a component of the MTUC7000AWS laundry series, is a premium stackable washer and dryer that combines efficiency with cutting-edge technology and robust features. Designed for those who value both form and function, this unit is ideal for compact spaces without compromising on performance.

One of the standout features of the Maytag MTUC7000AWS is its high-efficiency washing capability. The unit employs a powerful motor that enables it to handle larger loads while using less water and energy. This not only reduces your utility bills but also lessens the environmental impact, aligning with sustainable living ideals.

A key technology integrated into this washer is the PowerWash cycle. This intelligent system is designed to tackle the toughest stains and dirt. It combines a robust wash action with prolonged wash times, ensuring that clothes come out cleaner than ever. Additionally, the washer's Advanced Vibration Control technology minimizes noise and vibrations, making it a perfect choice for apartments or homes where quiet operation is necessary.

Another notable characteristic of the MTUC7000AWS is its user-friendly interface. Equipped with a digital display and intuitive controls, users can easily select from multiple wash settings, tailoring cycles to their specific needs. The unit includes various preset cycles for delicates, bulky items, and more, providing versatility for varying fabric types.

The design of the Maytag MTUC7000AWS reflects both elegance and practicality. With a sleek finish and compact dimensions, it fits seamlessly into small laundry areas while still offering a large capacity. It also features a durable build quality, known to stand the test of time, ensuring that customers receive reliable performance for years to come.

Additionally, the Maytag brand is synonymous with dependability, backed by a robust warranty and customer service support. The washer is engineered with the latest technology that enhances its longevity, including a stainless steel drum that resists chipping and snagging.

In summary, the Maytag W10190314A in the MTUC7000AWS model stands out for its high efficiency, advanced stain-fighting features, user-friendly interface, and durable construction, making it an exceptional choice for those seeking a high-quality laundry solution in a compact form factor.
Top Page Image Contents