Rotel RSP-1066 Manual: Comprehensive Guide to Your Stereo Receiver

room when the sensors on the source compo- nents are blocked by installation in a cabinet. See your authorized Rotel dealer for information on IR repeater systems.

NOTE: The EXT REM IN jack located to the right of these jacks is for use with an external IR sensor duplicating the front-panel IR sen- sor and located in the primary zone. It should not be used for ZONE 2 IR connections.

On-Screen Display and System Configuration

The RSP-1066 features two on-screen systems to help operate the system. The first consists of simple status displays that appear on the TV screen whenever primary settings (Volume, Input, etc.) are changed. These status displays are self-explanatory.

A more comprehensive ON-SCREEN DISPLAY menu system is available at any time by pressing the MENU button on the remote control. These menus guide you through the setup and op- eration of the RSP-1066.

System Set-Up:System setup should be done while using a Composite video or S-Video cable connecting the RSP-1066 TV MONITOR out- puts to the video input of the TV or projector. No other video connections should be made at this time. Select OSD ( ON-SCREEN MENU) from the RR-969 remote control to complete system setup.

NOTE: On a PAL standard monitor, the OSD cannot be displayed until a video signal is present, irrespective of the type of video cables in use. For setup, connect the Com- posite video output from your DVD player and select its input on the RSP-1066. The OSD will be displayed as an overlay to the video signal from the DVD player.

The ON-SCREEN MENU system can be con- figured to display one of two languages: En- glish or German. If you would like to change from the default English language, see the in- structions for the OTHER OPTIONS menu later in this manual.

Navigation Buttons

The following remote control buttons are used to navigate the ON-SCREEN DISPLAY menu system:

GUIDE

	C	UP	M	K
		UP
L			OSD
M	-	ENT +		M
		DWN	PREV CH
	S	DWN	R
	S		R
	SEARCH –		SEARCH +

MENU Button : To display the MAIN screen. All other menus are reached from this menu. If a menu is already visible, push this button to cancel the display.

DOWN/UP Buttons : To move up and

down in the lists that appear on the ON- SCREEN DISPLAY menu system.

+/– Buttons : To change the current set- tings for a selected menu choice on some menus in the ON-SCREEN DISPLAY menu system.

ENTER Button : To confirm a setting and return to the MAIN menu.

NOTE: A help system at the bottom of each ON-SCREEN DISPLAY menu reminds you which buttons to press.

SYSTEM STATUS Menu

SYSTEM STATUS

LISTEN:	Tuner
RECORD:	VIDEO 1
MODE:	Stereo
INPUT:	Analog
VOLUME:	45

ZONE: Off
ENT KEY=MAIN MENU
OSD KEY=EXIT	V1.1

The SYSTEM STATUS menu provides a snap- shot of the current system settings and a start- ing point for reaching all other screens and menus. This screen appears when you press the MENU button on the remote control and displays the following information:

English

LISTEN: the source selected for listening.

RECORD: the source selected for the VIDEO and AUDIO outputs.

MODE: the current surround sound mode.

INPUT: the input selected for the current source: Optical, Coaxial, Analog, etc.

VOLUME: the current volume setting.

ZONE: the current status of ZONE 2, ON or OFF.

VERSION: the version of the operating soft- ware currently installed in the RSP-1066. Your unit may have a different version than shown here.

No changes can be made using this screen; it only provides information. To go to the rest of the menus, press the ENTER button to go to the MAIN menu. Press the MENU key on the remote to cancel the display and return to normal operation.

NOTE: The SYSTEM STATUS screen appears for ten seconds when the unit is turned on and automatically turns off.

MAIN Menu

MAIN MENU

INPUT SPEAKER

DELAY TEST TONE

SUB LEVEL ZONE 2

OTHER DEFAULT

ENT KEY=ENTER

UP KEY=up DWN KEY=down

The MAIN menu provides access to eight other screens and menus and is reached by press- ing the ENTER button from the SYSTEM STA- TUS menu described above or from most other menus. To go to another menu, move the high- light to the desired line using the UP/DOWN buttons on the remote and press the ENTER button. Press the MENU key on the remote to cancel the display and return to normal op- eration.